D-Link TM DES-6500, Manual

Page: 78 / 352

DES-6500 Chassis-based Layer 3 Ethernet Switch Manual
77
VLAN if the tag in the packet header is concurrent with this protocol. This packet header
information is defined by Novell NetWare 802.3 (IPX - Internet Packet Exchange).
ipx802dot2 - Using this parameter will instruct the Switch to forward packets to this
VLAN if the tag in the packet header is concurrent with this protocol. This packet header
information is defined by Novell NetWare 802.2 (IPX - Internet Packet Exchange).
ipxSnap - Using this parameter will instruct the Switch to forward packets to this VLAN if
the tag in the packet header is concurrent with this protocol. This packet header
information is defined by Novell and the Sub Network Access Protocol (SNAP).
ipxEthernet2 - Using this parameter will instruct the Switch to forward packets to this
VLAN if the tag in the packet header is concurrent with this protocol. This packet header
information is defined by Novell Ethernet II Protocol.
appleTalk - Using this parameter will instruct the Switch to forward packets to this VLAN
if the tag in the packet header is concurrent with this protocol. This packet header
information is defined by the AppleTalk protocol.
decLAT - Using this parameter will instruct the Switch to forward packets to this VLAN if
the tag in the packet header is concurrent with this protocol. This packet header
information is defined by the Digital Equipment Corporation (DEC) Local Area Transport
(LAT) protocol.
sna802dot2 - Using this parameter will instruct the Switch to forward packets to this
VLAN if the tag in the packet header is concurrent with this protocol. This packet header
information is defined by the Systems Network Architecture (SNA) 802.2 Protocol.
snaEthernet2 - Using this parameter will instruct the Switch to forward packets to this
VLAN if the tag in the packet header is concurrent with this protocol. This packet header
information is defined by the Systems Network Architecture (SNA) Ethernet II Protocol.
netBios - Using this parameter will instruct the Switch to forward packets to this VLAN if
the tag in the packet header is concurrent with this protocol. This packet header
information is defined by the NetBIOS Protocol.
xns - Using this parameter will instruct the Switch to forward packets to this VLAN if the
tag in the packet header is concurrent with this protocol. This packet header information
is defined by the Xerox Network Systems (XNS) Protocol.
vines - Using this parameter will instruct the Switch to forward packets to this VLAN if
the tag in the packet header is concurrent with this protocol. This packet header
information is defined by the Banyan Virtual Integrated Network Service (VINES)
Protocol.
ipV6 - Using this parameter will instruct the Switch to forward packets to this VLAN if the
tag in the packet header is concurrent with this protocol. This packet header information
is defined by the Internet Protocol Version 6 (IPv6) Protocol.
userDefined - Using this parameter will instruct the Switch to forward packets to this
VLAN if the tag in the packet header is concurrent with this protocol defined by the user.
This packet header information is defined by entering the following information:
User Defined Pid - Specifies that the VLAN will only accept packets with this
hexadecimal 802.1Q Ethernet type value in the packet header. The user may define an
entry, in the hexadecimal form (ffff) to define the packet identification. (The user only
need enter the final four integers of the hexadecimal format to define the packet ID –
{hex 0x0 0xffff})
This field is only operable if userDefined is selected in the Protocol ID
field.
encap [ethernet | llc | snap | all] – Specifies that the Switch will examine the octet of the
packet header referring to one of the protocols listed (Ethernet, LLC or SNAP), looking
for a match of the hexadecimal value previously entered .
all will instruct the Switch to
examine the total packet header. After a match is found, the Switch will forward the
packet to this VLAN. This field is only operable if
userDefined is selected in the Protocol
ID field.