Crystal Vision TANDEM-200 User Manual Download Page 141

Page: 141 / 141

Crystal Vision

Specification

TANDEM-200 User Manual R1.7

140

13/02/2008

RS4: Embedded digital audio re-sampler sub-module

Synchronisation

Synchronous audio to video 48Khz

Asynchronous audio to video 48kHz ± 50ppm

Total harmonic
distortion

0.00017% THD+N rms

Signal to noise

-117 dBFS, 22Hz to 22kHz typ

DIP2RS: Dual digital audio input re-sampler sub-module

Audio input

2 x 20 bit stereo pairs. AES3 110 Ohm or HiZ (balanced) D Type, or
AES3-id (unbalanced) 75 Ohm BNC. Set by on-board links.

Synchronisation

Asynchronous audio to video 30kHz to 108kHz sample rates

Total harmonic
distortion

0.00017% THD+N rms

Signal to noise

-117 dBFS, 22Hz to 22kHz typ

DOP2-110 and DOP2-75: Dual digital audio output sub-modules

Audio output

2 x 20 bit AES/EBU stereo pairs. DOP2-110, 110 Ohm or DOP2-75
(unbalanced) 75 Ohm BNC. Factory configuration only

Each of the two AES signal outputs has a second buffered output, which
may be available dependant on the RM module fitted.

Reference

Available instead of 2

buffered output on some rear connector modules.

Link selected

May be AES reference or Word clock – link select

Summary of Contents for TANDEM-200














































































































































Search results

Summary of Contents for TANDEM-200

Reviews:

Related manuals for TANDEM-200

Brands by name

Popular brands

Crystal Vision TANDEM-200, User Manual

Search results

Summary of Contents for TANDEM-200

Reviews:

Related manuals for TANDEM-200

Brands by name

Popular brands