Crystal Vision TANDEM-200 User Manual Download Page 106

Page: 106 / 141

Crystal Vision

Using card edge controls

TANDEM-200 User Manual R1.7

105

13/02/2008

9.15 Miscellaneous

functions

Firmware version number

The TANDEM-200 firmware version number is obtained with MENU DIL, lever 6 ON
(DOWN), all other levers UP (OFF

)

and the SEL switch in position C.

SEL

Display

Comments

TANDEM 5.53

TANDEM firmware version number

Note:

SEL position C provides information for Crystal Vision technical staff only.

BFormat test

The BFormat test menu is obtained with MENU DIL, lever 3 ON (DOWN) and all other
levers UP (OFF

)

SEL

Display

Comments

Bformat = XX

‘B’ card test where ‘X’= Y (Yes), N ( No), ‘-’ ( no card)
1

character = side 1 card ; 2

character = side 2 card

Share n/a

Not used by TANDEM-200

Engineering info

For Crystal Vision engineering staff only

This menu tests for the presence of ‘B’ format option cards, which are required for Mode
4 operation.

Note:

Additional menus are for Crystal Vision engineering staff only

Summary of Contents for TANDEM-200














































































































































Search results

Summary of Contents for TANDEM-200

Reviews:

Related manuals for TANDEM-200

Brands by name

Popular brands

Crystal Vision TANDEM-200, User Manual

Search results

Summary of Contents for TANDEM-200

Reviews:

Related manuals for TANDEM-200

Brands by name

Popular brands