manualshive.com logo in svg

Claas LEXION 480, Repair Manual

The Claas LEXION 480 Repair Manual is a comprehensive guide for maintaining and repairing your combine harvester. Easily download the manual for free from manualshive.com, ensuring you have all the necessary information to keep your machine running smoothly and efficiently. Get your hands on the manual now.

Share
Download
background image

188 678.1 - RHB LEXION 480 

11.1.1

Index

INDEX

Numerical

3-D sieve pan control system ................................................. 4.4.1
3-D sieve pan hydraulic cylinder, 
disassembled ....................................................................... 9.6.29
3-D upper sieve frame, disassembled  ................................. 4.2.15

A

Accelerator ............................................................................. 3.3.1
Accelerator, disassembled ................................................... 3.3.17
Adjusting pivot arm (A) with the “3-D gauge”  ......................... 4.4.2
Adjusting the 3-D sieve pan control system ........................... 4.4.1
Adjusting the axial rotor intermediate drive (19)  .................... 7.3.2
Adjusting the axial rotor step drive (18)  ................................. 7.3.1
Adjusting the concave potentiometer ................................... 3.2.21
Adjusting the cutterbar hydraulic cylinders  .......................... 9.5.12
Adjusting the master brake cylinder ....................................... 2.4.2
Adjusting the steering axle end stops  ................................ 7.21.15
Adjusting the trough and the lateral panel
(if suction blower with drive is fitted)  ...................................... 8.1.7
Air conditioner ........................................................................ 2.1.1
Air conditioner compressor Sanden Sd 7h 15, 
disassembled ....................................................................... 2.1.12
Air conditioning system – Topping up refrigerant ................... 2.1.3
Air conditioning system (cab side), 
disassembled ....................................................................... 2.1.22
Alternator ............................................................................... 1.3.1
Alternator ............................................................................... 2.5.1
Assembling and installing the axial rotor 
intermediate drive V-belt pulley ............................................ 7.15.4
Assembling and installing the clean grain 
elevator head  ......................................................................... 5.2.7
Assembling and installing the cutterbar 
drive deflection pulley (2) with a cutterbar
variable-speed drive fitted .................................................... 7.4.43
Assembling and installing the electric fan 
variable-speed pulley assembly ......................................... 7.14.33
Assembling and installing the fan blade bearing .................... 6.2.8
Assembling and installing the jockey pulley 
of straw chopper drive (10)  ................................................ 7.10.11
Assembling and installing the jockey pulley 
of straw chopper drive (11)  ................................................ 7.10.13
Assembling and installing the rotary screen  .......................... 8.1.4
Assembling and installing the rotary screen drive ................ 7.17.4
Assembling and installing the rotary screen 
suction blower ...................................................................... 8.1.12
Assembling and installing the stage 1 
chopper drive V-belt pulley  .................................................. 7.10.4
Assembling and installing the stage 2 
chopper drive V-belt pulley  .................................................. 7.10.9
Assembling and installing the stage 3 
chopper drive V-belt pulley  ................................................ 7.10.18
Assembling the planetary final drive gearbox  .................... 7.18.23
Assembling the 3-D sieve pan 
hydraulic cylinder  ................................................................. 9.6.30
Assembling the Autopilot steering cylinder  .......................... 9.7.10
Assembling the axial rotor gearbox .................................... 7.15.16
Assembling the bottom feed rake roller  ............................... 3.1.21

Assembling the CLAAS Autopilot solenoid valve  ................  9.8.20
Assembling the concave adjustment 
hydraulic cylinder .................................................................  9.5.22
Assembling the concave adjustment 
pressure relief valve  ..............................................................  9.8.4
Assembling the concave and grain tank 
unloading tube 4/3-way valves  ............................................  9.8.14
Assembling the concave, grain tank 
unloading tube and straw chopper 4/3-way valves  .............  9.8.11
Assembling the cutterbar cross levelling 
hydraulic cylinders .................................................................  9.5.4
Assembling the cutterbar drive V-belt pulley 
with a cutterbar variable-speed drive fitted ..........................  7.4.40
Assembling the cutterbar hydraulic cylinder  ........................  9.5.11
Assembling the cutterbar variable-speed 
pulley assembly (hydraulic)  .................................................  7.4.50
Assembling the cutterbar variable-speed 
pulley assembly (spring-loaded) ..........................................  7.4.31
Assembling the differential  ................................................  7.19.11
Assembling the engine speed control 
hydraulic cylinder
(from serial no. ...)  ...............................................................  9.6.12
Assembling the engine speed control 
hydraulic cylinder
(up to serial no. ...)  ..............................................................  9.6.24
Assembling the fan adjustment (electric)
(Version 1) .........................................................................  7.14.10
Assembling the fan adjustment (electric)
(Version 1, version 3)  ........................................................  7.14.18
Assembling the fan adjustment (electric)
(Version 2) .........................................................................  7.14.26
Assembling the fan variable-speed pulley 
assembly (spring-loaded)  ..................................................  7.14.41
Assembling the feed rake conveyor 
suction blower  .......................................................................  3.1.8
Assembling the final drive gearbox  .....................................  7.18.7
Assembling the front sieve pan drive 
deflection pulley ...................................................................  7.13.5
Assembling the grain tank unloading 
engagement hydraulic cylinder ..............................................  9.6.7
Assembling the grain tank unloading tube 
swing hydraulic cylinder  ......................................................  9.5.26
Assembling the left-hand bearing assembly ........................  3.3.11
Assembling the lower grain tank 
unloading angle drive
(from serial no. ...)  ...............................................................  5.3.19
Assembling the lower grain tank 
unloading angle drive
(up to serial no. ...)  ..............................................................  5.3.28
Assembling the low-pressure 
solenoid valve block  ............................................................  9.8.23
Assembling the main valve ..................................................  9.8.17
Assembling the manual gearbox  .......................................  7.19.16
Assembling the master brake cylinder  ..................................  2.4.1
Assembling the pendulum control unit 
for 3-D sieve pan  .................................................................  9.6.34

Index

Summary of Contents for LEXION 480



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for LEXION 480

Taurus B450 Assembly Instructions Manual preview
B450
Brand: Taurus Pages: 28
Kärcher HDS Series Operator'S Manual preview
HDS Series
Brand: Kärcher Pages: 54
ABB 2 Series Operation And Installation Manual preview
2 Series
Brand: ABB Pages: 85
Landoll 850 Series Supplement Manual preview
850 Series
Brand: Landoll Pages: 6
ParaBody 827 Assembly Instruction Sheet preview
827
Brand: ParaBody Pages: 9
ParaBody 828 Assembly Instructions preview
828
Brand: ParaBody Pages: 3
MacDon 802 Operator'S Manual preview
802
Brand: MacDon Pages: 45
H&S 8200 Series Operator'S Manual preview
8200 Series
Brand: H&S Pages: 30
Eclipse Combustion 6500 Instruction Manual preview
6500
Brand: Eclipse Combustion Pages: 46
Bard Duet Instructions For Use preview
Duet
Brand: Bard Pages: 2
MacDon R216 Quick Card preview
R216
Brand: MacDon Pages: 2
MacDon R216 Operator'S Manual preview
R216
Brand: MacDon Pages: 214
MacDon R216 Installation Instructions Manual preview
R216
Brand: MacDon Pages: 32
4iQ 4 Happy Kids GUCIO Manual preview
4 Happy Kids GUCIO
Brand: 4iQ Pages: 12
4iiii FLiiiight Owner'S Manual preview
FLiiiight
Brand: 4iiii Pages: 36
4iiii FLiiiight User Manual preview
FLiiiight
Brand: 4iiii Pages: 34
4EVAC IMPACT Reference Manual preview
IMPACT
Brand: 4EVAC Pages: 27
LAWO crystal User Manual preview
crystal
Brand: LAWO Pages: 459

Brands by name

Popular brands

Load more brands