manualshive.com logo in svg

Claas LEXION 480, Repair Manual

The Claas LEXION 480 Repair Manual is a comprehensive guide for maintaining and repairing your combine harvester. Easily download the manual for free from manualshive.com, ensuring you have all the necessary information to keep your machine running smoothly and efficiently. Get your hands on the manual now.

Share
Download
background image

0.1.6

 RHB LEXION 480 - 188 678.1

Contents

Assembling the cutterbar drive V-belt pulley 
with a cutterbar variable-speed drive fitted  .................... 7.4.40
Installing the cutterbar drive V-belt pulley 
with a cutterbar variable-speed drive fitted  .................... 7.4.42
Removing and disassembling the cutterbar drive 
deflection pulley (2) with a cutterbar 
variable-speed drive fitted .............................................. 7.4.42
Assembling and installing the cutterbar drive 
deflection pulley (2) with a cutterbar 
variable-speed drive fitted .............................................. 7.4.43
Removing the cutterbar variable-speed 
pulley assembly (hydraulic)  ........................................... 7.4.43
Disassembling the cutterbar variable-speed 
pulley assembly (hydraulic)  ........................................... 7.4.46
Cutterbar variable-speed pulley assembly 
(hydraulic), disassembled  .............................................. 7.4.48
Assembling the cutterbar variable-speed 
pulley assembly (hydraulic)  ........................................... 7.4.50
Installing the cutterbar variable-speed 
pulley assembly (hydraulic)  ........................................... 7.4.51
Removing the cutterbar clutch  ....................................... 7.4.52
Cutterbar clutch, disassembled  ..................................... 7.4.59
Installing the cutterbar clutch  ......................................... 7.4.60

Left-hand threshing mechanism drive .................................... 7.5.1

Removing the threshing mechanism drive 
pulley assembly  ............................................................... 7.5.1
Threshing mechanism drive pulley assembly, 
disassembled ................................................................... 7.5.7
Installing the threshing mechanism drive 
pulley assembly  ............................................................... 7.5.8

Right-hand threshing mechanism drive  ................................. 7.6.1

Removing the threshing drum variable-speed 
pulley assembly (hydraulic)  ............................................. 7.6.1
Disassembling the threshing drum 
variable-speed pulley assembly (hydraulic) ..................... 7.6.2
Threshing drum variable-speed pulley assembly 
(hydraulic), disassembled  ................................................ 7.6.4
Assembling the threshing drum variable-speed 
pulley assembly (hydraulic)  ............................................. 7.6.6
Installing the threshing drum variable-speed 
pulley assembly (hydraulic)  ............................................. 7.6.6
Removing the threshing drum variable-speed 
pulley assembly (spring-loaded)  ...................................... 7.6.7
Disassembling the threshing drum 
variable-speed pulley assembly (spring-loaded)  ............. 7.6.8
Threshing drum variable-speed pulley assembly 
(spring-loaded), disassembled ....................................... 7.6.11
Assembling the threshing drum variable-speed 
pulley assembly (spring-loaded)  .................................... 7.6.12
Installing the threshing drum variable-speed 
pulley assembly (spring-loaded)  .................................... 7.6.16
Removing the threshing mechanism 
drive pulley ..................................................................... 7.6.18
Disassembling the threshing mechanism 
drive pulley ..................................................................... 7.6.18
Threshing mechanism drive pulley, 
disassembled ................................................................. 7.6.20

Assembling the threshing mechanism 
drive pulley  ....................................................................  7.6.21
Installing the threshing mechanism 
drive pulley  ....................................................................  7.6.23

Threshing drum reduction gearbox ........................................  7.7.1

Removing the threshing drum 
reduction gearbox ............................................................  7.7.1
Disassembling the threshing drum 
reduction gearbox ............................................................  7.7.2
Threshing drum reduction gearbox, 
disassembled ..................................................................  7.7.6
Assembling the threshing drum 
reduction gearbox ............................................................  7.7.8
Installing the threshing drum 
reduction gearbox ..........................................................  7.7.11

Threshing mechanism intermediate drive ..............................  7.8.1

Removing the right-hand intermediate 
drive shaft bearing ...........................................................  7.8.1
Installing the right-hand intermediate 
drive shaft bearing ...........................................................  7.8.2
Removing the left-hand intermediate 
drive shaft bearing ...........................................................  7.8.2
Installing the left-hand intermediate 
drive shaft bearing ...........................................................  7.8.3
Removing the intermediate drive shaft ............................  7.8.4
Installing the intermediate drive shaft ..............................  7.8.4

Grain tank unloading drive .....................................................  7.9.1

Removing the grain tank unloading 
drive pulley  ......................................................................  7.9.1
Installing the grain tank unloading 
drive pulley  ......................................................................  7.9.3

Chopper drive  ......................................................................  7.10.1

Removing the stage 1 chopper 
drive V-belt pulley ..........................................................  7.10.1
Stage 1 chopper drive V-belt pulley, 
disassembled ................................................................  7.10.3
Assembling and installing the stage 1 
chopper drive V-belt pulley ............................................  7.10.4
Removing the stage 2 chopper 
drive V-belt pulley ..........................................................  7.10.6
Stage 2 chopper drive V-belt pulley, 
disassembled ................................................................  7.10.8
Assembling and installing the stage 2 chopper 
drive V-belt pulley ..........................................................  7.10.9
Removing the jockey pulley of 
straw chopper drive (10) ..............................................  7.10.11
Jockey pulley of straw chopper drive (10), 
disassembled ..............................................................  7.10.11
Assembling and installing the jockey pulley 
of straw chopper drive (10) ..........................................  7.10.11
Removing the jockey pulley of 
straw chopper drive (11) ..............................................  7.10.12
Jockey pulley of straw chopper drive (11), 
disassembled ..............................................................  7.10.12
Assembling and installing the jockey pulley 
of straw chopper drive (11) ..........................................  7.10.13
Removing the stage 3 chopper 
drive V-belt pulley ........................................................  7.10.13

Summary of Contents for LEXION 480



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for LEXION 480

Landoll 2210 Operator'S Manual preview
2210
Brand: Landoll Pages: 52
JBSYSTEMS Light Premium Operation Manual preview
Premium
Brand: JBSYSTEMS Light Pages: 14
YardShape 2600 Owner'S Manual preview
2600
Brand: YardShape Pages: 50
KaVo K4 Operating Instructions Manual preview
K4
Brand: KaVo Pages: 13
vc999 K3 Operating Instruction preview
K3
Brand: vc999 Pages: 52
7th Sense medialon Showmaster Go User'S Reference Manual preview
medialon Showmaster Go
Brand: 7th Sense Pages: 9
e+p Elektrik Handels HDT 300 Quick Installation Manual preview
HDT 300
Brand: e+p Elektrik Handels Pages: 2
Quick DP Series Installation And User Manual preview
DP Series
Brand: Quick Pages: 24
JDS Uniphase SmartClass E1 User Manual preview
SmartClass E1
Brand: JDS Uniphase Pages: 144
JDS Uniphase IP Video Test Option HST-3000 Instruction Manual preview
IP Video Test Option HST-3000
Brand: JDS Uniphase Pages: 14
K-9 Lights Bulldog User Manual preview
Bulldog
Brand: K-9 Lights Pages: 12
K'Nex Education 79319 Manual preview
79319
Brand: K'Nex Education Pages: 2
EASY COOPS Chicken Coop Plan 3x5 Assembly Instructions Manual preview
Chicken Coop Plan 3x5
Brand: EASY COOPS Pages: 21
EASY COOPS Chicken Coop Plan 4x6 Assembly Instructions Manual preview
Chicken Coop Plan 4x6
Brand: EASY COOPS Pages: 18
EASY COOPS Chicken Coop Plan 8x10 Assembly Instructions Manual preview
Chicken Coop Plan 8x10
Brand: EASY COOPS Pages: 18
XanLite LR126 User Manual preview
LR126
Brand: XanLite Pages: 2
X-Rite i1Display Setup Manual preview
i1Display
Brand: X-Rite Pages: 6
Qlight S180U Manual preview
S180U
Brand: Qlight Pages: 4

Brands by name

Popular brands

Load more brands