manualshive.com logo in svg

Claas LEXION 480, Repair Manual

The Claas LEXION 480 Repair Manual is a comprehensive guide for maintaining and repairing your combine harvester. Easily download the manual for free from manualshive.com, ensuring you have all the necessary information to keep your machine running smoothly and efficiently. Get your hands on the manual now.

Share
Download
background image

188 678.1 - RHB LEXION 480 

7.4.17

Cutterbar drive

Removing the rear pulley of cutterbar drive (1)

(from serial no. ...)

Remove the cutterbar drive belt (1) at the rear – see 
page 7.2.1, 

Removing the cutterbar drive belt (1) (Cut-

terbar drive without variable-speed drive)

.

Removing the impeller drive belt (4)

, see page 7.2.7

DANGER!

Follow the correct order of work steps when 
releasing the tension of spring-loaded 
cylinder 

– Danger of injury!

Remove the three hex. bolts and remove the cover.

(Fig. 44)

Remove the hex. bolt from the face end of impeller.

(Fig. 45)

Screw the head-centred hex. bolt M 12 x 30 into the 
shaft.

Remove the V-belt pulley using the special tool.

(Fig. 46, 47)

44

45

46

Summary of Contents for LEXION 480



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for LEXION 480

Bartscher 700 Series Instructions For Installation, Use And Maintenance Manual preview
700 Series
Brand: Bartscher Pages: 22
KaVo 4040 Operating, Maintenance And Assembly Instructions preview
4040
Brand: KaVo Pages: 16
Eclipse Combustion 6500 Instruction Manual preview
6500
Brand: Eclipse Combustion Pages: 46
Bard Duet Instructions For Use preview
Duet
Brand: Bard Pages: 2
GE ImageQuant LAS 4000 Original Instructions Manual preview
ImageQuant LAS 4000
Brand: GE Pages: 86
GE AKTApure Operating Instructions Manual preview
AKTApure
Brand: GE Pages: 160
GE AKTA avant Getting Started preview
AKTA avant
Brand: GE Pages: 134
Yamaha V50 Use Manual preview
V50
Brand: Yamaha Pages: 78
Fast 8200 Operation Manual preview
8200
Brand: Fast Pages: 42
DARAY V60 Manual preview
V60
Brand: DARAY Pages: 28
Backyard Play Systems 4500 Assembly Manual preview
4500
Brand: Backyard Play Systems Pages: 64
Haenim 3G Manual preview
3G
Brand: Haenim Pages: 2
JB Systems Sirius Operation Manual preview
Sirius
Brand: JB Systems Pages: 7
3B SCIENTIFIC PHYSICS 1023095 Instruction Sheet preview
1023095
Brand: 3B SCIENTIFIC PHYSICS Pages: 36
3A HEALTH CARE HAPPYNEB III Instruction Manual preview
HAPPYNEB III
Brand: 3A HEALTH CARE Pages: 16
360 Systems Short/cut 2000 Audio Editor Specification preview
Short/cut 2000 Audio Editor
Brand: 360 Systems Pages: 4
ACE INSTRUMENTS AFM-5 Quick Start Manual preview
AFM-5
Brand: ACE INSTRUMENTS Pages: 2
ODA LP Series User Manual preview
LP Series
Brand: ODA Pages: 103

Brands by name

Popular brands

Load more brands