manualshive.com logo in svg

Claas LEXION 480, Repair Manual

The Claas LEXION 480 Repair Manual is a comprehensive guide for maintaining and repairing your combine harvester. Easily download the manual for free from manualshive.com, ensuring you have all the necessary information to keep your machine running smoothly and efficiently. Get your hands on the manual now.

Share
Download
background image

188 678.1 - RHB LEXION 480 

0.1.5

Contents

Installing and adjusting the sieve pan 
drive belt (15) ................................................................. 7.2.31
Removing the uni-spreader drive belt (16)  .................... 7.2.32
Installing and adjusting the uni-spreader 
drive belt (16) ................................................................. 7.2.33
Removing the grain tank unloading 
drive chain (17) .............................................................. 7.2.34
Installing and adjusting the grain tank 
unloading drive chain (17)  ............................................. 7.2.35

Right-hand drive belts  ............................................................ 7.3.1

Adjusting the axial rotor step drive (18)  ........................... 7.3.1
Adjusting the axial rotor intermediate 
drive (19)  ......................................................................... 7.3.2
Removing the fan intermediate drive belt (20) ................. 7.3.3
Installing and adjusting the fan 
intermediate drive belt (20) .............................................. 7.3.4
Removing the fan drive belt (21)  ..................................... 7.3.5
Installing and adjusting the fan drive belt (21)  ................. 7.3.5
Removing the threshing mechanism 
variable-speed drive belt (22)  .......................................... 7.3.6
Installing and adjusting the threshing 
mechanism variable-speed drive belt (22) ....................... 7.3.7
Removing the threshing drum drive belt (23) ................... 7.3.8
Installing and adjusting the threshing 
drum drive belt (23)  ......................................................... 7.3.9
Removing the accelerator drive belt (24) ....................... 7.3.10
Installing and adjusting the accelerator 
drive belt (24) ................................................................. 7.3.11
Removing the radiator chaff screen 
intermediate drive belt (25) ............................................ 7.3.12
Installing and adjusting the rotary chaff screen 
intermediate drive belt (25) ............................................ 7.3.13
Removing the radiator chaff screen drive 
belt (26)  ......................................................................... 7.3.14
Installing and adjusting the rotary chaff screen 
drive belt (26) ................................................................. 7.3.14
Removing the fan drive belt (27)  ................................... 7.3.15
Installing and adjusting the fan drive belt (27)  ............... 7.3.16
Removing the suction blower drive belt (28) .................. 7.3.17
Installing and adjusting the suction blower 
drive belt (28) ................................................................. 7.3.18
Removing the air conditioner compressor 
drive belt (29) ................................................................. 7.3.19
Installing and adjusting the air conditioner 
compressor drive belt (29)  ............................................. 7.3.20
Removing the compressed-air compressor 
drive belt (30) ................................................................. 7.3.21
Installing and adjusting the compressed-air 
compressor drive belt (30)  ............................................. 7.3.22
Removing the alternator drive belt (31)  ......................... 7.3.23
Installing and adjusting the alternator 
drive belt (31) ................................................................. 7.3.24
Removing the feed rake conveyor suction 
blower drive belt (34)  ..................................................... 7.3.26
Installing and adjusting the feed rake conveyor 
suction blower drive belt (34) ......................................... 7.3.27
Removing the straw spreader drive belt (36) ................. 7.3.28

Installing and adjusting the straw spreader 
drive belt (36)  ................................................................  7.3.29

Cutterbar drive .......................................................................  7.4.1

Removing the front pulley of cutterbar 
drive (1)  ...........................................................................  7.4.1
Installing the front pulley of cutterbar drive (1)  ................  7.4.2
Removing the deflection pulley 
of cutterbar drive (1)  ........................................................  7.4.2
Deflection pulley of cutterbar drive (1), 
disassembled ..................................................................  7.4.3
Installing the deflection pulley 
of cutterbar drive (1)  ........................................................  7.4.3
Removing the slip clutch of cutterbar drive (1) ................  7.4.3
Installing the slip clutch of cutterbar drive (1) ..................  7.4.4
Replacing the slip clutch linings 
of cutterbar drive (1)  ........................................................  7.4.5
Slip clutch of cutterbar drive (1), dismantled  ...................  7.4.5
Removing the jockey pulley of cutterbar 
drive (1)  ...........................................................................  7.4.7
Jockey pulley of cutterbar drive (1), 
disassembled ..................................................................  7.4.7
Removing the rear pulley of cutterbar drive (1)
(up to serial no. ...)  ..........................................................  7.4.7
Dismantling the rear pulley of cutterbar drive (1)
(up to serial no. ...)  ........................................................  7.4.10
Rear pulley of cutterbar drive (1), disassembled
(up to serial no. ...)  ........................................................  7.4.12
Assembling the rear pulley of cutterbar drive (1)
(up to serial no. ...)  ........................................................  7.4.13
Installing the rear pulley of cutterbar drive (1)
(up to serial no. ...)  ........................................................  7.4.15
Removing the rear pulley of cutterbar drive (1)
(from serial no. ...)  .........................................................  7.4.17
Dismantling the rear pulley of cutterbar drive (1)
(from serial no. ...)  .........................................................  7.4.20
Rear pulley of cutterbar drive (1), disassembled
(from serial no. ...)  .........................................................  7.4.22
Assembling the rear pulley of cutterbar drive (1)
(from serial no. ...)  .........................................................  7.4.23
Installing the rear pulley of cutterbar drive (1)
(from serial no. ...)  .........................................................  7.4.24
Removing the cutterbar variable-speed 
pulley assembly (spring-loaded)  ...................................  7.4.26
Disassembling the cutterbar variable-speed 
pulley assembly (spring-loaded)  ...................................  7.4.27
Cutterbar variable-speed pulley assembly 
(spring-loaded), disassembled  ......................................  7.4.30
Assembling the cutterbar variable-speed 
pulley assembly (spring-loaded)  ...................................  7.4.31
Installing the cutterbar variable-speed 
pulley assembly (spring-loaded)  ...................................  7.4.35
Removing the cutterbar drive V-belt pulley 
when a cutterbar variable-speed drive is fitted ..............  7.4.37
Disassembling the cutterbar drive V-belt pulley 
when a cutterbar variable-speed drive is fitted ..............  7.4.37
Cutterbar drive V-belt pulley with a cutterbar 
variable-speed drive fitted, disassembled  .....................  7.4.39

Summary of Contents for LEXION 480



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for LEXION 480

BANLAW 800 Series Product Data Sheet preview
800 Series
Brand: BANLAW Pages: 32
Baker Instrument Company D6000 Digital Troubleshooting Procedures & Fault Listing preview
D6000
Brand: Baker Instrument Company Pages: 24
DARKSTAR TECHNOLOGIES D340 Manual To Operation preview
D340
Brand: DARKSTAR TECHNOLOGIES Pages: 4
TDW D2000 Maintenance Manuallines preview
D2000
Brand: TDW Pages: 2
Taurus 1170 Assembly And Operating Instructions Manual preview
1170
Brand: Taurus Pages: 25
Vancare G Series Quick Reference Manual preview
G Series
Brand: Vancare Pages: 3
Paitec ES-2000 User Manual preview
ES-2000
Brand: Paitec Pages: 14
LAWO crystal User Manual preview
crystal
Brand: LAWO Pages: 459
earline 60700 User Information preview
60700
Brand: earline Pages: 13
LaserLiner ActiveFinder One Manual preview
ActiveFinder One
Brand: LaserLiner Pages: 92
Valmar 2055 Operator'S Manual preview
2055
Brand: Valmar Pages: 78
Valhalla Scientific 4176 Operation Manual preview
4176
Brand: Valhalla Scientific Pages: 64
Varimixer ERGO60 Operating Instructions Manual preview
ERGO60
Brand: Varimixer Pages: 28
EFX EFF523 Instructions For Use preview
EFF523
Brand: EFX Pages: 2
Hammer Strength HDT-MAB Assembly Manual preview
HDT-MAB
Brand: Hammer Strength Pages: 8
Ublox EVK-M8F-0-00 User Manual preview
EVK-M8F-0-00
Brand: Ublox Pages: 22
Harris 9250-05 Operator'S Manual preview
9250-05
Brand: Harris Pages: 21
Nakayama ES7250 Manual preview
ES7250
Brand: Nakayama Pages: 19

Brands by name

Popular brands

Load more brands