Claas LEXION 480 Repair Manual Download Page 997

Page: 997 / 1018

188 678.1 - RHB LEXION 480

10.3.5

Engine

Mark hydraulic lines (H) and unscrew at the solenoid
valves. Plug the hydraulic connections tightly.

(Fig. 17)

Unscrew the cover and remove cable from the
magnetic pick-up (G).

Unscrew the mounting bracket (W) and the clamp (S).

(Fig. 18)

Remove mounting plate (L) and unhook the hydraulic
cylinder.

Loosen the jockey pulley (S) and remove the belt from
the lever. The hydraulic cylinder and the lever overlap.

Remove the belt guide at (O).

Unscrew guide (F) and pull it out.

(Fig. 19)

Remove castellated nut and pull off the V-belt pulley
using a special tool.

Ensure that the pulley, the jockey pulley arm and the
belt guide will not tilt.

(Fig. 20)

Summary of Contents for LEXION 480



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for LEXION 480

Reviews:

Related manuals for LEXION 480

Brands by name

Popular brands

Claas LEXION 480, Repair Manual

Search results

Summary of Contents for LEXION 480

Reviews:

Related manuals for LEXION 480

Brands by name

Popular brands