manualshive.com logo in svg

Claas LEXION 480, Repair Manual

The Claas LEXION 480 Repair Manual is a comprehensive guide for maintaining and repairing your combine harvester. Easily download the manual for free from manualshive.com, ensuring you have all the necessary information to keep your machine running smoothly and efficiently. Get your hands on the manual now.

Share
Download
background image

5.2.2

 RHB LEXION 480 - 188 678.1

Grain elevator

Remove the two cover plates (A and B) at the elevator 
head.

(Fig. 5)

Pull the elevator chain out from the top.

(Fig. 6)

Installing the clean grain elevator chain

1. Introduce the elevator chain into the elevator from 

the top. Observe correct installation position!

2. Connect the two ends of the chain with the chain 

connector at the bottom.

3. Tension the chain using the hex. nut (M) so far that 

the paddles do not scrape the elevator housing. It 
must be possible to push the conveyor chain to 
the side manually at the bottom chain wheel. 
Secure the adjustment with the lock nut (G).

(Fig. 3)

4. Close inspection door (B) and bolt down 

guard (C).

(Fig. 1, 2)

5. Bolt down cover plates (A and B).

(Fig. 5)

5

6

Summary of Contents for LEXION 480



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for LEXION 480

Rangevision PRO Setup And Calibration Instructions preview
PRO
Brand: Rangevision Pages: 31
Bartscher 1500/17 Original Instruction Manual preview
1500/17
Brand: Bartscher Pages: 28
Bartscher IV-65 Instruction Manual preview
IV-65
Brand: Bartscher Pages: 13
IBEX TS100 Quick Start Manual preview
TS100
Brand: IBEX Pages: 10
M-system R3 Series Instruction Manual preview
R3 Series
Brand: M-system Pages: 12
Madsen zodiac Reference Manual preview
zodiac
Brand: Madsen Pages: 206
Valcom V-9972 Quick Start Manual preview
V-9972
Brand: Valcom Pages: 6
Vaisala HUMICAP HMP4 User Manual preview
HUMICAP HMP4
Brand: Vaisala Pages: 60
Varian Saturn 2000 GC/MS Pre-Installation Instructions preview
Saturn 2000 GC/MS
Brand: Varian Pages: 9
Mako MK5 Operator'S Manual preview
MK5
Brand: Mako Pages: 17
Balluff BOS R254K-UUI-LH10-S4 Installation Manual preview
BOS R254K-UUI-LH10-S4
Brand: Balluff Pages: 12
Gardena 1815 Operating Instructions Manual preview
1815
Brand: Gardena Pages: 33
Backyard Adventures Playcenter Belmont Owners Manual And Assemly Instruction preview
Belmont
Brand: Backyard Adventures Playcenter Pages: 33
A.HABERKORN KS 45 Instructions For Use And Test Manual preview
KS 45
Brand: A.HABERKORN Pages: 28
Quadro mdb A0317 Construction Manual preview
A0317
Brand: Quadro mdb Pages: 9
NAMYSLO DEEP Series Manual preview
DEEP Series
Brand: NAMYSLO Pages: 13
Masterclock CS5-LAN User Manual preview
CS5-LAN
Brand: Masterclock Pages: 19
Kattsafe SL1 Operation Manual preview
SL1
Brand: Kattsafe Pages: 19

Brands by name

Popular brands

Load more brands