manualshive.com logo in svg

Claas LEXION 480, Repair Manual

The Claas LEXION 480 Repair Manual is a comprehensive guide for maintaining and repairing your combine harvester. Easily download the manual for free from manualshive.com, ensuring you have all the necessary information to keep your machine running smoothly and efficiently. Get your hands on the manual now.

Share
Download
background image

0.1.10

 RHB LEXION 480 - 188 678.1

Contents

Assembling the engine speed control 
hydraulic cylinder
(from serial no. ...) .......................................................... 9.6.12
Pre-setting the engine speed control 
hydraulic cylinder
(from serial no. ...) .......................................................... 9.6.14
Installing the engine speed control 
hydraulic cylinder
(from serial no. ...) .......................................................... 9.6.14
Setting the engine speed control 
hydraulic cylinder
(from serial no. ...) .......................................................... 9.6.15
Changing the road travel engine speed 
(country variants 20 km/h and/or 25 km/h) 
by converting the cylinder  .............................................. 9.6.16
Conversion of cylinder to another country 
variant (20 km/h and/or 25 km/h) ................................... 9.6.16
Removing the engine speed control 
hydraulic cylinder
(up to serial no. ...) ......................................................... 9.6.19
Disassembling the engine speed control 
hydraulic cylinder
(up to serial no. ...) ......................................................... 9.6.20
Engine speed control hydraulic cylinder,
disassembled 
(up to serial no. …

) ........................................................... 9.6.23

Assembling the engine speed control 
hydraulic cylinder
(up to serial no. ...) ......................................................... 9.6.24
Pre-setting the engine speed control 
hydraulic cylinder
(up to serial no. ...) ......................................................... 9.6.25
Installing the engine speed control 
hydraulic cylinder
(up to serial no. ...) ......................................................... 9.6.25
Setting the engine speed control 
hydraulic cylinder
(up to serial no. ...) ......................................................... 9.6.26
Removing the 3-D sieve pan 
hydraulic cylinder  ........................................................... 9.6.28
Disassembling the 3-D sieve pan 
hydraulic cylinder  ........................................................... 9.6.28
3-D sieve pan hydraulic cylinder, 
disassembled ................................................................. 9.6.29
Assembling the 3-D sieve pan 
hydraulic cylinder  ........................................................... 9.6.30
Installing the 3-D sieve pan 
hydraulic cylinder  ........................................................... 9.6.31
Removing the pendulum control unit 
of the 3-D sieve pan ....................................................... 9.6.31
Disassembling the 3-D sieve pan 
pendulum control unit  .................................................... 9.6.31
Pendulum control unit of 3-D sieve pan, 
disassembled ................................................................. 9.6.33
Assembling the pendulum control unit 
for 3-D sieve pan  ........................................................... 9.6.34
Installing the 3-D sieve pan pendulum 
control unit  ..................................................................... 9.6.34

Removing the yield meter moisture sensor 
hydraulic cylinder ...........................................................  9.6.35
Disassembling the yield meter moisture 
sensor hydraulic cylinder ...............................................  9.6.36
Yield meter moisture sensor hydraulic cylinder, 
disassembled ................................................................  9.6.37
Assembling the yield meter moisture 
sensor hydraulic cylinder ...............................................  9.6.37
Installing the yield meter moisture 
sensor hydraulic cylinder ...............................................  9.6.38
Checking and adjusting the yield meter 
hydraulic cylinder ...........................................................  9.6.38
Yield meter hydraulic cylinder, 
disassembled ................................................................  9.6.40

Hydraulic cylinders – Steering hydraulics ..............................  9.7.1

Removing the steering cylinder  .......................................  9.7.1
Disassembling the steering cylinder ................................  9.7.1
Steering cylinder, disassembled ......................................  9.7.3
Assembling the steering cylinder .....................................  9.7.4
Installing the steering cylinder  .........................................  9.7.5
Removing the Autopilot steering cylinder  ........................  9.7.5
Disassembling the Autopilot steering cylinder .................  9.7.6
Autopilot steering cylinder, disassembled  .......................  9.7.9
Assembling the Autopilot steering cylinder ....................  9.7.10
Installing the Autopilot steering cylinder  ........................  9.7.11

Valve combinations  ...............................................................  9.8.1

Removing the feeder reversing 3/2-way valve  ................  9.8.1
Feeder reversing 3/2-way valve, 
disassembled ..................................................................  9.8.1
Removing the cutterbar cross levelling 
4/3-way valve  ..................................................................  9.8.2
Cutterbar cross levelling 4/3-way valve, 
disassembled ..................................................................  9.8.3
Removing the concave adjustment 
pressure relief valve  ........................................................  9.8.4
Concave adjustment pressure relief valve, 
disassembled ..................................................................  9.8.4
Assembling the concave adjustment 
pressure relief valve  ........................................................  9.8.4
Removing the cutterbar and threshing drum 
variable-speed drive 3/3-way valves  ...............................  9.8.4
Cutterbar and threshing drum
variable-speed drive 3/3-way valve, 
disassembled ..................................................................  9.8.6
Installing the cutterbar and threshing drum 
variable-speed drive 3/3-way valves  ...............................  9.8.7
Removing the threshing drum variable-speed 
drive 3/3-way valve ..........................................................  9.8.7
Threshing drum variable-speed 
drive 3/3-way valve, disassembled ..................................  9.8.8
Removing the concave, grain tank unloading 
tube and straw chopper 4/3-way valves  ..........................  9.8.9
Concave, grain tank unloading tube and 
straw chopper 4/3-way valve, disassembled .................  9.8.10
Assembling the concave, grain tank unloading 
tube and straw chopper 4/3-way valves  ........................  9.8.11
Installing the concave, grain tank unloading 
tube and straw chopper 4/3-way valves  ........................  9.8.11

Summary of Contents for LEXION 480



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for LEXION 480

CAMPAGNOLA HERCULES Quick Manual preview
HERCULES
Brand: CAMPAGNOLA Pages: 4
Fayat Group BOMAG BT 60 Operating Instructions Manual preview
BOMAG BT 60
Brand: Fayat Group Pages: 50
Halyard MIC Instructions For Use Manual preview
MIC
Brand: Halyard Pages: 88
Nemalux LS Series Manual preview
LS Series
Brand: Nemalux Pages: 6
OBDLink LX Quick Start Manual preview
LX
Brand: OBDLink Pages: 2
Radial Engineering StageBug SB-2 Quick Start Manual preview
StageBug SB-2
Brand: Radial Engineering Pages: 2
Radial Engineering Dragster Quick Start preview
Dragster
Brand: Radial Engineering Pages: 2
Mako MK5 Operator'S Manual preview
MK5
Brand: Mako Pages: 17
Balluff BOS R254K-UUI-LH10-S4 Installation Manual preview
BOS R254K-UUI-LH10-S4
Brand: Balluff Pages: 12
Fast RH15 Owner'S Manual preview
RH15
Brand: Fast Pages: 60
GE Innova IGS 6 Preinstallation Manual preview
Innova IGS 6
Brand: GE Pages: 194
Major tech MT474 Instruction Manual preview
MT474
Brand: Major tech Pages: 12
Meritor RS 120 Maintenance Manual preview
RS 120
Brand: Meritor Pages: 65
Marani DPA360P User Manual preview
DPA360P
Brand: Marani Pages: 35
Falcon Haymakers Hooimakers F80-350V Operator'S Manual preview
Haymakers Hooimakers F80-350V
Brand: Falcon Pages: 38
Lightronics FXLE17C4N Owner'S Manual preview
FXLE17C4N
Brand: Lightronics Pages: 6
Neopost IM 30 Operator'S Manual preview
IM 30
Brand: Neopost Pages: 10
KAM KSD2 Instruction Manual preview
KSD2
Brand: KAM Pages: 8

Brands by name

Popular brands

Load more brands