manualshive.com logo in svg

Claas LEXION 480, Repair Manual

The Claas LEXION 480 Repair Manual is a comprehensive guide for maintaining and repairing your combine harvester. Easily download the manual for free from manualshive.com, ensuring you have all the necessary information to keep your machine running smoothly and efficiently. Get your hands on the manual now.

Share
Download
background image

11.1.2

 RHB LEXION 480 - 188 678.1

Index

Assembling the rear pulley of 
cutterbar drive (1)
(from serial no. ...) ................................................................ 7.4.23
Assembling the rear pulley of 
cutterbar drive (1)
(up to serial no. ...)  ............................................................... 7.4.13
Assembling the rear sieve pan drive 
deflection pulley  ................................................................... 7.13.7
Assembling the returns elevator  ............................................ 5.1.9
Assembling the reverser drive 
hydraulic cylinder  ................................................................. 9.5.34
Assembling the right-hand bearing  ........................................ 3.3.3
Assembling the rotary coupling ............................................ 9.5.17
Assembling the steering column  ............................................ 2.2.8
Assembling the steering cylinder  ........................................... 9.7.4
Assembling the straw chopper drive 
hydraulic cylinder  ................................................................. 9.5.29
Assembling the straw spreader 
bearing housing  ................................................................... 7.11.7
Assembling the threshing drum 
reduction gearbox  .................................................................. 7.7.8
Assembling the threshing drum variable-speed 
pulley assembly (hydraulic) .................................................... 7.6.6
Assembling the threshing drum variable-speed 
pulley assembly (spring-loaded)  .......................................... 7.6.12
Assembling the threshing mechanism 
drive pulley ........................................................................... 7.6.21
Assembling the threshing mechanism 
engagement hydraulic cylinder  .............................................. 9.6.3
Assembling the transfer gearbox  ....................................... 7.16.12
Assembling the uni-spreader hydraulic pump  ........................ 9.3.3
Assembling the upper grain tank 
unloading angle drive ........................................................... 5.3.35
Assembling the yield meter moisture 
sensor hydraulic cylinder  ..................................................... 9.6.37
Autopilot steering cylinder, 
disassembled ......................................................................... 9.7.9
Axial rotor drive  .................................................................... 7.15.1
Axial rotor drive jockey pulley (18), 
disassembled ....................................................................... 7.15.6
Axial rotor gearbox, disassembled ..................................... 7.15.15
Axial rotor intermediate drive V-belt pulley, 
disassembled ....................................................................... 7.15.3
Axial rotors  ............................................................................. 3.6.1

B

Basic concave setting  .......................................................... 3.2.16
Basic rule  ............................................................................... 1.2.3
Bearing of axial rotors drive (18), 
disassembled ....................................................................... 7.15.9
Bleeding the brake system ................................................... 7.20.2
Bleeding the cutterbar cross levelling 
hydraulic cylinders  ................................................................. 9.5.6
Bleeding the shifter piston .................................................. 7.19.28
Bolts ....................................................................................... 1.4.1
Bottom feed rake roller, 
disassembled ....................................................................... 3.1.21
Brake .................................................................................... 7.20.1
Brake line screw joints  ........................................................... 1.4.3

C

Centre cleaning fan bearing, 
disassembled .........................................................................  4.6.9
Changing the hydraulic oil  .....................................................  9.2.2
Changing the road travel engine speed 
(country variants 20 km/h and/or 25 km/h) 
by converting the cylinder ....................................................  9.6.16
Checking / topping up the refrigerant oil level 
at the air conditioner compressor  ..........................................  2.1.4
Checking and adjusting the alignment 
of preparation floor and sieve pan  .......................................  4.2.24
Checking and adjusting the yield meter 
hydraulic cylinder .................................................................  9.6.38
Checking the oil level .............................................................  9.2.1
Chopper drive  ......................................................................  7.10.1
CLAAS Autopilot solenoid valve, 
disassembled .......................................................................  9.8.19
Clean grain elevator head, 
disassembled .........................................................................  5.2.6
Cleaning fan  ..........................................................................  4.6.1
Cleaning fan bearing, 
disassembled .........................................................................  4.6.4
Compressor-type air conditioner  ...........................................  1.2.3
Concave adjustment hydraulic cylinder, 
disassembled .......................................................................  9.5.21
Concave adjustment pressure relief valve, 
disassembled .........................................................................  9.8.4
Concave and grain tank unloading tube 
4/3-way valve, disassembled ...............................................  9.8.13
Concave, grain tank unloading tube and 
straw chopper 4/3-way valve, disassembled  .......................  9.8.10
Conversion of cylinder to another country variant 
(20 km/h and/or 25 km/h)  ....................................................  9.6.16
Cooling system  ....................................................................  10.1.1
Correct installation of adapter sleeve bearings  .....................  1.3.2
Correct installation of lock collar bearings  .............................  1.3.2
Correct use of the machine  ...................................................  1.2.2
Cutterbar and threshing drum variable-speed 
drive 3/3-way valve, disassembled ........................................  9.8.6
Cutterbar clutch, disassembled  ...........................................  7.4.59
Cutterbar cross levelling 4/3-way valve, 
disassembled .........................................................................  9.8.3
Cutterbar cross levelling hydraulic cylinder, 
disassembled .........................................................................  9.5.3
Cutterbar drive .......................................................................  7.4.1
Cutterbar drive V-belt pulley with a cutterbar 
variable-speed drive fitted, 
disassembled .......................................................................  7.4.39
Cutterbar hydraulic cylinder, 
disassembled .......................................................................  9.5.10
Cutterbar hydraulic cylinders – 
Replacing the seals  ...............................................................  9.5.7
Cutterbar variable-speed pulley assembly 
(hydraulic), disassembled ....................................................  7.4.48
Cutterbar variable-speed pulley assembly 
(spring-loaded), disassembled  ............................................  7.4.30
Cutting cylinder, disassembled ............................................  6.1.11

Summary of Contents for LEXION 480



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for LEXION 480

iGuzzini B183 Instruction Sheet preview
B183
Brand: iGuzzini Pages: 20
GE RGB1-G60-8 Use And Care Instructions preview
RGB1-G60-8
Brand: GE Pages: 2
GE Druck DPI 620 Genii Quick Start Manual preview
Druck DPI 620 Genii
Brand: GE Pages: 154
GE Arize Element Top Light Mounting Installation Manual preview
Arize Element Top Light
Brand: GE Pages: 2
Datex-Ohmeda Aestiva/5 Operation Manual preview
Aestiva/5
Brand: Datex-Ohmeda Pages: 104
Baker Hughes Druck DPI 620 Genii Instruction Manual preview
Druck DPI 620 Genii
Brand: Baker Hughes Pages: 166
Baker Hughes Druck DPI 620 Genii Safety And Quick Start Manual preview
Druck DPI 620 Genii
Brand: Baker Hughes Pages: 340
Panasonic HF Series Quick Start Manual preview
HF Series
Brand: Panasonic Pages: 9
ICS ELECTRONICS 4803 Quick Start Manual preview
4803
Brand: ICS ELECTRONICS Pages: 6
C.M.O FL Series Instruction And Maintenance Manual preview
FL Series
Brand: C.M.O Pages: 10
Federal 90 Series Troubleshooting Manual preview
90 Series
Brand: Federal Pages: 43
Jackson DISHSTAR ADA-SEER Operation Manual preview
DISHSTAR ADA-SEER
Brand: Jackson Pages: 2
Nederman NEX S User Manual preview
NEX S
Brand: Nederman Pages: 89
Nederman MagnaTrack ST User Manual preview
MagnaTrack ST
Brand: Nederman Pages: 71
Nederman 30S Series User Manual preview
30S Series
Brand: Nederman Pages: 131
X-Cite TURBO Quick Start Manual preview
TURBO
Brand: X-Cite Pages: 2
Yamaha MagicStomp Effect List preview
MagicStomp
Brand: Yamaha Pages: 31
GE PWS Operating And Maintenance Instructions Manual preview
PWS
Brand: GE Pages: 18

Brands by name

Popular brands

Load more brands