manualshive.com logo in svg

Claas LEXION 480, Repair Manual

The Claas LEXION 480 Repair Manual is a comprehensive guide for maintaining and repairing your combine harvester. Easily download the manual for free from manualshive.com, ensuring you have all the necessary information to keep your machine running smoothly and efficiently. Get your hands on the manual now.

Share
Download
background image

0.1.8

 RHB LEXION 480 - 188 678.1

Contents

Installing the bearings of axial rotors 
drive (18) ...................................................................... 7.15.10
Removing the axial rotors drive  ................................... 7.15.11
Disassembling the axial rotor gearbox ......................... 7.15.12
Axial rotor gearbox, disassembled ............................... 7.15.15
Assembling the axial rotor gearbox  ............................. 7.15.16
Installing the axial rotor gearbox .................................. 7.15.20

Engine output ....................................................................... 7.16.1

Removing the engine output pulley  ............................... 7.16.1
Installing the engine output pulley  ................................. 7.16.1
Removing the transfer gearbox  ..................................... 7.16.2
Disassembling the transfer gearbox  .............................. 7.16.7
Transfer gearbox, disassembled  ................................. 7.16.11
Assembling the transfer gearbox  ................................. 7.16.12
Installing the transfer gearbox  ..................................... 7.16.19

Rotary screen drive .............................................................. 7.17.1

Removing the rotary screen drive .................................. 7.17.1
Disassembling the rotary screen drive ........................... 7.17.1
Rotary screen drive, disassembled ................................ 7.17.3
Assembling and installing the rotary screen drive  ......... 7.17.4
Removing the fan drive .................................................. 7.17.5
Installing the fan drive .................................................... 7.17.5

Final drives ........................................................................... 7.18.1

Removing the final drive gearbox  .................................. 7.18.1
Disassembling the final drive gearbox  ........................... 7.18.1
Removing the wheel drive shaft ..................................... 7.18.1
Removing the intermediate shaft  ................................... 7.18.3
Removing the drive shaft  ............................................... 7.18.5
Final drive gearbox, disassembled  ................................ 7.18.6
Assembling the final drive gearbox ................................ 7.18.7
Installing the drive shaft  ................................................. 7.18.7
Installing the intermediate shaft  ..................................... 7.18.8
Installing the wheel drive shaft ..................................... 7.18.11
Disassembling the planetary 
final drive gearbox  ....................................................... 7.18.15
Planetary final drive gearbox, 
disassembled ............................................................... 7.18.22
Assembling the planetary 
final drive gearbox  ....................................................... 7.18.23
Installing the final drive gearbox  .................................. 7.18.27

Manual gearbox  ................................................................... 7.19.1

Removing the manual gearbox ...................................... 7.19.1
Disassembling the manual gearbox ............................... 7.19.3
Removing the shifter rails  .............................................. 7.19.3
Removing the drive shaft  ............................................... 7.19.5
Removing the main shaft  ............................................... 7.19.6
Removing the differential  ............................................... 7.19.8
Disassembling the differential ........................................ 7.19.9
Differential, disassembled ............................................ 7.19.11
Assembling the differential ........................................... 7.19.11
Installing the differential  ............................................... 7.19.13
Manual gearbox, disassembled  ................................... 7.19.15
Assembling the manual gearbox  ................................. 7.19.16
Installing the main shaft  ............................................... 7.19.17
Installing the drive shaft  ............................................... 7.19.18
Installing the shifter rails  .............................................. 7.19.19
Installing the manual gearbox ...................................... 7.19.22
Servo gearshift ............................................................. 7.19.25

Removing the shifter pistons  .......................................  7.19.25
Servo gearshift, disassembled  ....................................  7.19.27
Installing the shifter pistons  .........................................  7.19.27
Bleeding the shifter piston  ...........................................  7.19.28

Brake ...................................................................................  7.20.1

Parking brake – Replacing the brake linings  .................  7.20.1
Bleeding the brake system  ............................................  7.20.2
Disc brake – Changing the brake pads  .........................  7.20.2
Removing a brake calliper .............................................  7.20.3
Installing a brake calliper ...............................................  7.20.4

Steering axle ........................................................................  7.21.1

Removing the wheel bearing .........................................  7.21.1
Wheel bearing, disassembled  .......................................  7.21.4
Installing the wheel bearing ...........................................  7.21.5
Removing the stub axle .................................................  7.21.7
Stub axle, disassembled  .............................................  7.21.10
Installing the stub axle .................................................  7.21.10
Setting the track width  .................................................  7.21.13
Adjusting the steering axle end stops ..........................  7.21.15
Removing the steering axle .........................................  7.21.16
Steering axle bearing, disassembled  ..........................  7.21.18
Installing the steering axle ...........................................  7.21.19

8. Machine body

Rotary screen  ........................................................................  8.1.1

Removing the rotary screen  ............................................  8.1.1
Disassembling the rotary screen  .....................................  8.1.1
Rotary screen, disassembled  ..........................................  8.1.3
Assembling and installing the rotary screen ....................  8.1.4
Trough and lateral panel, disassembled  .........................  8.1.6
Adjusting the trough and the lateral panel
(if suction blower with drive is fitted) ................................  8.1.7
Removing the fan drive  ...................................................  8.1.8
Installing the fan drive  .....................................................  8.1.8
Removing the rotary screen suction blower  ....................  8.1.9
Disassembling the rotary screen suction blower  .............  8.1.9
Rotary screen suction blower, disassembled  ................  8.1.11
Assembling and installing the rotary screen 
suction blower  ...............................................................  8.1.12

Drive axle ...............................................................................  8.2.1

Removing the drive axle ..................................................  8.2.1
Installing the drive axle ....................................................  8.2.4

9. Hydraulic system

Oil cooler  ...............................................................................  9.1.1

Removing the oil cooler ...................................................  9.1.1
Installing the oil cooler .....................................................  9.1.4

Maintenance ..........................................................................  9.2.1

Hydraulic system  .............................................................  9.2.1
Checking the oil level  ......................................................  9.2.1
Changing the hydraulic oil  ...............................................  9.2.2
Filling instructions when changing the hydraulic oil .........  9.2.3

Hydraulic pumps ....................................................................  9.3.1

Removing the uni-spreader hydraulic pump ....................  9.3.1
Disassembling the uni-spreader hydraulic pump  ............  9.3.2
Uni-spreader hydraulic pump, disassembled  ..................  9.3.3
Assembling the uni-spreader hydraulic pump  .................  9.3.3
Installing the uni-spreader hydraulic pump ......................  9.3.4
Removing the ground drive hydraulic pump ....................  9.3.4

Summary of Contents for LEXION 480



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for LEXION 480

ABB Relion 670 series Communication Protocol Manual preview
Relion 670 series
Brand: ABB Pages: 66
Rath 2100 Installation & Operation Manual preview
2100
Brand: Rath Pages: 3
Ecco 3800 Series Assembly, Installation And Operation Instructions preview
3800 Series
Brand: Ecco Pages: 9
Talet Equipment 3000 Series Parts & Operators Manual preview
3000 Series
Brand: Talet Equipment Pages: 17
Hanna Instruments HI 98311 Instruction Manual preview
HI 98311
Brand: Hanna Instruments Pages: 2
Hanna Instruments HI981520 Quick Reference Manual preview
HI981520
Brand: Hanna Instruments Pages: 2
Hanna HALO 2 Instruction Manual preview
HALO 2
Brand: Hanna Pages: 12
Hanil T04 User Manual preview
T04
Brand: Hanil Pages: 24
Hanil Supra R17 User Manual preview
Supra R17
Brand: Hanil Pages: 32
Hanil Component R12 Operation Manual preview
Component R12
Brand: Hanil Pages: 24
laerdal SimMan 3G Trauma Quick Setup Manual preview
SimMan 3G Trauma
Brand: laerdal Pages: 16
laerdal SimMan 3G Maintenance Manual preview
SimMan 3G
Brand: laerdal Pages: 16
laerdal SimMan Important Product Information preview
SimMan
Brand: laerdal Pages: 60
laerdal Nursing Baby Manual preview
Nursing Baby
Brand: laerdal Pages: 4
laerdal Resusci Anne Simulator Important Product Information preview
Resusci Anne Simulator
Brand: laerdal Pages: 8
laerdal Nursing Baby VitalSim Manual preview
Nursing Baby VitalSim
Brand: laerdal Pages: 15
NanoVibronix UROSHIELD Quick Manual preview
UROSHIELD
Brand: NanoVibronix Pages: 2
NanoVibronix PainShield User Manual preview
PainShield
Brand: NanoVibronix Pages: 32

Brands by name

Popular brands

Load more brands