manualshive.com logo in svg

Claas LEXION 480, Repair Manual

The Claas LEXION 480 Repair Manual is a comprehensive guide for maintaining and repairing your combine harvester. Easily download the manual for free from manualshive.com, ensuring you have all the necessary information to keep your machine running smoothly and efficiently. Get your hands on the manual now.

Share
Download
background image

188 678.1 - RHB LEXION 480 

0.1.3

Contents

Removing the return pan  ................................................. 4.1.3
Rear rocker arm, disassembled ....................................... 4.1.5
Installing the return pan  ................................................... 4.1.5

Sieve pan ............................................................................... 4.2.1

Removing and installing the sieves  ................................. 4.2.1
Removing the upper sieves
(from serial no. ...)  ........................................................... 4.2.1
Removing the lower sieves
(from serial no. ...)  ........................................................... 4.2.3
Installing the sieves
(from serial no. ...)  ........................................................... 4.2.4
Tightening torques of axial mountings 
for the upper and lower sieves
(from serial no. ...)  ........................................................... 4.2.4
Sieves – Basic setting
(electric sieve adjustment – from serial no. ...)  ................ 4.2.5
Removing the upper sieves
(up to serial no. ...) ........................................................... 4.2.5
Removing the lower sieves
(up to serial no. ...) ........................................................... 4.2.7
Installing the sieves
(up to serial no. ...) ........................................................... 4.2.8
Tightening torques of axial mountings 
for the upper and lower sieves
(up to serial no. ...) ........................................................... 4.2.9
Sieves – Basic setting
(electric sieve adjustment – up to serial no. ...)  ............... 4.2.9
Removing the 3-D upper sieve frame  ............................ 4.2.10
3-D upper sieve frame, disassembled  ........................... 4.2.15
Installing the 3-D upper sieve frame  .............................. 4.2.16
Removing the sieve pan  ................................................ 4.2.17
Sieve pan, disassembled ............................................... 4.2.20
Installing the sieve pan  .................................................. 4.2.21
Checking and adjusting the alignment 
of preparation floor and sieve pan  ................................. 4.2.24

Preparation floor  .................................................................... 4.3.1

Removing the preparation floor  ....................................... 4.3.1
Preparation floor, disassembled  ...................................... 4.3.3
Installing the preparation floor  ......................................... 4.3.4

3-D sieve pan control system ................................................. 4.4.1

Adjusting the 3-D sieve pan control system ..................... 4.4.1
Adjusting pivot arm (A) with the “3-D gauge” ................... 4.4.2

Rocker arm drive .................................................................... 4.5.1

Removing the intermediate drive shaft 
for the rocker arm drive ................................................... 4.5.1
Intermediate drive shaft for rocker arm drive, 
disassembled ................................................................... 4.5.2
Installing the intermediate drive shaft 
for the rocker arm drive ................................................... 4.5.3

Cleaning fan ........................................................................... 4.6.1

Removing the bearings of the cleaning fan  ..................... 4.6.1
Cleaning fan bearing, disassembled  ............................... 4.6.4
Installing the cleaning fan bearing  ................................... 4.6.4
Removing the cleaning fan shaft  ..................................... 4.6.5
Removing the centre cleaning fan bearing  ...................... 4.6.9
Centre cleaning fan bearing, disassembled  .................... 4.6.9
Installing the cleaning fan shaft  ..................................... 4.6.10
Removing the cleaning fan rotors  .................................. 4.6.11

Installing the cleaning fan rotors  ...................................  4.6.11
Removing the cleaning fan housing  ..............................  4.6.12
Installing the cleaning fan housing  ................................  4.6.14

5. Grain delivery

Returns elevator  ....................................................................  5.1.1

Removing the returns elevator chain  ..............................  5.1.1
Installing the returns elevator chain  ................................  5.1.3
Removing the top returns auger ......................................  5.1.3
Installing the top returns auger ........................................  5.1.5
Removing the returns elevator  ........................................  5.1.6
Disassembling the returns elevator  .................................  5.1.7
Assembling the returns elevator ......................................  5.1.9
Installing the returns elevator  ..........................................  5.1.9
Removing the returns elevator boot  ..............................  5.1.10
Installing the returns elevator boot  ................................  5.1.11
Removing the lower returns auger  ................................  5.1.11
Installing the lower returns auger  ..................................  5.1.13

Grain elevator ........................................................................  5.2.1

Removing the clean grain elevator chain  ........................  5.2.1
Installing the clean grain elevator chain  ..........................  5.2.2
Removing the clean grain elevator head .........................  5.2.3
Dismantling the clean grain elevator head  ......................  5.2.4
Clean grain elevator head, disassembled  .......................  5.2.6
Assembling and installing the clean grain 
elevator head  ..................................................................  5.2.7
Removing the clean grain elevator shaft  .........................  5.2.7
Installing the grain elevator shaft  ....................................  5.2.8
Removing the clean grain elevator boot ..........................  5.2.9
Installing the clean grain elevator boot ..........................  5.2.10
Removing the clean grain auger  ...................................  5.2.10
Installing the clean grain auger  .....................................  5.2.13
Removing the grain tank filler auger  .............................  5.2.14
Removing the grain tank filler auger 
angle drive .....................................................................  5.2.15
Disassembling the grain tank filler auger 
angle drive .....................................................................  5.2.16
Grain tank filler auger, disassembled  ............................  5.2.17
Installing the grain tank filler auger  ...............................  5.2.18

Grain tank unloading  .............................................................  5.3.1

Removing the grain tank cross auger  .............................  5.3.1
Grain tank cross augers, disassembled  ..........................  5.3.4
Installing the grain tank cross auger  ...............................  5.3.5
Removing the vertical grain tank 
unloading auger  ..............................................................  5.3.7
Installing the vertical grain tank 
unloading auger  ............................................................  5.3.10
Removing the horizontal grain tank 
unloading auger  ............................................................  5.3.11
Installing the horizontal grain tank 
unloading auger  ............................................................  5.3.13
Removing the lower grain tank 
unloading angle drive
(from serial no. ...)  .........................................................  5.3.13
Disassembling the lower grain tank 
unloading angle drive
(from serial no. ...)  .........................................................  5.3.15

Summary of Contents for LEXION 480



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for LEXION 480

NARGESA H1 Instruction Book preview
H1
Brand: NARGESA Pages: 33
Landoll 850 Series Supplement Manual preview
850 Series
Brand: Landoll Pages: 6
ParaBody 827 Assembly Instruction Sheet preview
827
Brand: ParaBody Pages: 9
ParaBody 828 Assembly Instructions preview
828
Brand: ParaBody Pages: 3
MacDon 802 Operator'S Manual preview
802
Brand: MacDon Pages: 45
H&S 8200 Series Operator'S Manual preview
8200 Series
Brand: H&S Pages: 30
Panasonic DVCPRO P2 Series Brochure & Specs preview
DVCPRO P2 Series
Brand: Panasonic Pages: 32
Yamaha A3000 Upgrade Manual preview
A3000
Brand: Yamaha Pages: 50
A&D PT Series Instruction Manual preview
PT Series
Brand: A&D Pages: 30
XAG P30 Quick Start Manual preview
P30
Brand: XAG Pages: 24
Parker RC Series Maintenance Instructions preview
RC Series
Brand: Parker Pages: 5
Bacharach Fyrite INSIGHT Operating & Maintenance Instructions preview
Fyrite INSIGHT
Brand: Bacharach Pages: 31
Backyard Play Systems 4105 Instruction Manual preview
4105
Brand: Backyard Play Systems Pages: 52
Backyard Play Systems 4030 Instructions Manual preview
4030
Brand: Backyard Play Systems Pages: 19
Backyard Play Systems 4030 Manual preview
4030
Brand: Backyard Play Systems Pages: 44
Bacharach Monoxor III Specification Sheet preview
Monoxor III
Brand: Bacharach Pages: 2
PANDROL CD100 User And Maintenance Manual preview
CD100
Brand: PANDROL Pages: 36
Badger Basket CABANA Assembly Instructions Manual preview
CABANA
Brand: Badger Basket Pages: 7

Brands by name

Popular brands

Load more brands