manualshive.com logo in svg

Claas LEXION 480, Repair Manual

The Claas LEXION 480 Repair Manual is a comprehensive guide for maintaining and repairing your combine harvester. Easily download the manual for free from manualshive.com, ensuring you have all the necessary information to keep your machine running smoothly and efficiently. Get your hands on the manual now.

Share
Download
background image

188 678.1 - RHB LEXION 480 

11.1.9

Index

Removing the jockey pulley 
of straw chopper drive (10)  ................................................ 7.10.11
Removing the jockey pulley 
of straw chopper drive (11)  ................................................ 7.10.12
Removing the left-hand drum bearing assembly  ................... 3.4.6
Removing the left-hand impeller bearing  ............................... 3.5.3
Removing the left-hand intermediate 
drive shaft bearing  ................................................................. 7.8.2
Removing the left-hand straw chopper bearing  ..................... 6.1.5
Removing the lower grain tank 
unloading angle drive
(from serial no. ...) ................................................................ 5.3.13
Removing the lower grain tank 
unloading angle drive
(up to serial no. ...) ............................................................... 5.3.23
Removing the lower returns auger ....................................... 5.1.11
Removing the lower sieves
(from serial no. ...) .................................................................. 4.2.3
Removing the lower sieves
(up to serial no. ...) ................................................................. 4.2.7
Removing the low-pressure solenoid valve 
(yield meter) ......................................................................... 9.8.23
Removing the low-pressure solenoid valve block  ................ 9.8.20
Removing the main concave .................................................. 3.2.7
Removing the main intermediate drive belt (7)  .................... 7.2.12
Removing the main shaft  ..................................................... 7.19.6
Removing the main valve ..................................................... 9.8.14
Removing the manual gearbox  ............................................ 7.19.1
Removing the master brake cylinder  ..................................... 2.4.1
Removing the oil cooler  ......................................................... 9.1.1
Removing the Orbitrol  .......................................................... 2.2.14
Removing the parking brake  .................................................. 2.3.1
Removing the pendulum control unit 
of the 3-D sieve pan ............................................................. 9.6.31
Removing the preconcave  ..................................................... 3.2.2
Removing the preparation floor .............................................. 4.3.1
Removing the radiator .......................................................... 10.1.3
Removing the radiator chaff screen drive 
belt (26) ................................................................................ 7.3.14
Removing the radiator chaff screen 
intermediate drive belt (25)  .................................................. 7.3.12
Removing the rear pulley of cutterbar drive (1)
(from serial no. ...) ................................................................ 7.4.17
Removing the rear pulley of cutterbar drive (1)
(up to serial no. ...) ................................................................. 7.4.7
Removing the rear sieve pan drive 
deflection pulley  ................................................................... 7.13.5
Removing the return pan  ....................................................... 4.1.3
Removing the returns elevator ............................................... 5.1.6
Removing the returns elevator boot ..................................... 5.1.10
Removing the returns elevator chain  ..................................... 5.1.1
Removing the reverser drive ................................................ 3.1.32
Removing the reverser drive hydraulic cylinder  ................... 9.5.32
Removing the reverser drive hydrostatic fixed 
displacement motor ................................................................ 9.4.5
Removing the right-hand drum 
bearing assembly ................................................................... 3.4.1
Removing the right-hand impeller bearing  ............................. 3.5.1

Removing the right-hand intermediate 
drive shaft bearing .................................................................  7.8.1
Removing the right-hand straw 
chopper bearing  ....................................................................  6.1.1
Removing the rotary screen  ..................................................  8.1.1
Removing the rotary screen drive  .......................................  7.17.1
Removing the rotary screen suction blower  ..........................  8.1.9
Removing the separating jacket  ............................................  3.6.3
Removing the separation grates  ...........................................  3.6.1
Removing the shifter pistons  .............................................  7.19.25
Removing the shifter rails ....................................................  7.19.3
Removing the sieve pan ......................................................  4.2.17
Removing the sieve pan drive belt (15) ...............................  7.2.29
Removing the sieve pan drive V-belt pulley  ........................  7.13.1
Removing the sieve pan intermediate 
drive belt (13)  ......................................................................  7.2.25
Removing the sieve pan intermediate 
drive belt (14)  ......................................................................  7.2.27
Removing the slip clutch of 
cutterbar drive (1)  ..................................................................  7.4.3
Removing the stage 1 chopper 
drive V-belt pulley ................................................................  7.10.1
Removing the stage 1 fan 
drive V-belt pulley ................................................................  7.14.1
Removing the stage 2 chopper 
drive V-belt pulley ................................................................  7.10.6
Removing the stage 3 chopper 
drive V-belt pulley ..............................................................  7.10.13
Removing the steering axle ...............................................  7.21.16
Removing the steering column ..............................................  2.2.2
Removing the steering cylinder  .............................................  9.7.1
Removing the stone trap  .......................................................  3.2.1
Removing the straw chopper drive 
belts (10 and 11)  .................................................................  7.2.20
Removing the straw chopper drive h
ydraulic cylinder ...................................................................  9.5.27
Removing the straw chopper 
intermediate drive belt (9) ....................................................  7.2.18
Removing the straw spreader bearing housing ...................  7.11.1
Removing the straw spreader drive belt (36)  ......................  7.3.28
Removing the stub axle .......................................................  7.21.7
Removing the suction blower drive belt (28)  .......................  7.3.17
Removing the thermostat  ....................................................  2.1.23
Removing the threshing drum  .............................................  3.4.10
Removing the threshing drum drive belt (23)  ........................  7.3.8
Removing the threshing drum reduction gearbox  .................  7.7.1
Removing the threshing drum shaft  ....................................  3.4.14
Removing the threshing drum variable-speed 
drive 3/3-way valve ................................................................  9.8.7
Removing the threshing drum variable-speed 
drive hydraulic cylinder ........................................................  9.5.30
Removing the threshing drum variable-speed 
pulley assembly (hydraulic)  ...................................................  7.6.1
Removing the threshing drum variable-speed 
pulley assembly (spring-loaded) ............................................  7.6.7
Removing the threshing mechanism 
drive pulley  ..........................................................................  7.6.18
Removing the threshing mechanism 

Summary of Contents for LEXION 480



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for LEXION 480

Salvis KTM Series Translation Of The Operating Instructions preview
KTM Series
Brand: Salvis Pages: 40
IDEAL 99 Assembly Instruction preview
99
Brand: IDEAL Pages: 2
Camozzi 50 Series Mounting Instructions preview
50 Series
Brand: Camozzi Pages: 2
Oktober 7 Operation Manual preview
7
Brand: Oktober Pages: 22
Baker Hughes Druck DPI 880 Instruction Manual preview
Druck DPI 880
Brand: Baker Hughes Pages: 168
ADVANCED HOME CARE Helios Manual preview
Helios
Brand: ADVANCED HOME CARE Pages: 16
Gearmore T230 Operation, Service And Parts Manual preview
T230
Brand: Gearmore Pages: 47
Xtool A30 Pro Manual preview
A30 Pro
Brand: Xtool Pages: 51
H-TEC Education D201 Operating Instructions Manual preview
D201
Brand: H-TEC Education Pages: 16
H-TEC Education A129 Operating Instructions Manual preview
A129
Brand: H-TEC Education Pages: 12
Haag-Streit BM 900 Instructions For Use Manual preview
BM 900
Brand: Haag-Streit Pages: 16
IEMCA KID 80 Manual For Use And Maintenance preview
KID 80
Brand: IEMCA Pages: 82
IEMCA KID 80-IV Touch Instruction Manual preview
KID 80-IV Touch
Brand: IEMCA Pages: 122
Calrec ARGO Installation & Technical Manual preview
ARGO
Brand: Calrec Pages: 92
DS Produkte XMLT-24ELED-200CA8-1 Instruction Manual preview
XMLT-24ELED-200CA8-1
Brand: DS Produkte Pages: 28
Fri-Jado STG 5-I Instructions Manual preview
STG 5-I
Brand: Fri-Jado Pages: 48
Janschitz Milky 13360 Operating Instruction preview
Milky 13360
Brand: Janschitz Pages: 40
Dangerous power FUSION FX Owner'S Manual preview
FUSION FX
Brand: Dangerous power Pages: 38

Brands by name

Popular brands

Load more brands