manualshive.com logo in svg

Claas LEXION 480, Repair Manual

The Claas LEXION 480 Repair Manual is a comprehensive guide for maintaining and repairing your combine harvester. Easily download the manual for free from manualshive.com, ensuring you have all the necessary information to keep your machine running smoothly and efficiently. Get your hands on the manual now.

Share
Download
background image

11.1.10

 RHB LEXION 480 - 188 678.1

Index

drive pulley assembly ............................................................. 7.5.1
Removing the threshing mechanism 
engagement hydraulic cylinder  .............................................. 9.6.1
Removing the threshing mechanism 
variable-speed drive belt (22)  ................................................ 7.3.6
Removing the top feed rake shaft  .......................................... 3.1.9
Removing the top returns auger  ............................................ 5.1.3
Removing the transfer gearbox ............................................ 7.16.2
Removing the uni-spreader drive angle drive  ...................... 7.12.1
Removing the uni-spreader drive belt (16) ........................... 7.2.32
Removing the uni-spreader hydraulic pump  .......................... 9.3.1
Removing the uni-spreader 
hydraulic pump drive belt (6) ................................................ 7.2.11
Removing the uni-spreader 
intermediate drive belt (12)  .................................................. 7.2.23
Removing the upper grain tank 
unloading angle drive ........................................................... 5.3.32
Removing the upper sieves
(from serial no. ...) .................................................................. 4.2.1
Removing the upper sieves
(up to serial no. ...)  ................................................................. 4.2.5
Removing the valve block from the Orbitrol  ......................... 2.2.11
Removing the vertical grain tank 
unloading auger  ..................................................................... 5.3.7
Removing the vertical unloading auger tube ........................ 5.3.41
Removing the wheel bearing  ............................................... 7.21.1
Removing the wheel drive shaft ........................................... 7.18.1
Removing the yield meter moisture 
sensor hydraulic cylinder  ..................................................... 9.6.35
Renewing the beater bars .................................................... 3.4.13
Replacing the accelerator caps ............................................ 3.3.13
Replacing the feeder chains  ................................................ 3.1.35
Replacing the free-swinging knives  ..................................... 6.1.13
Replacing the runners .......................................................... 3.1.25
Replacing the slip clutch linings 
of cutterbar drive (1) ............................................................... 7.4.5
Replacing the wooden ledges .............................................. 3.1.22
Return pan  ............................................................................. 4.1.1
Returns elevator ..................................................................... 5.1.1
Reverser drive hydraulic cylinder, 
disassembled ....................................................................... 9.5.33
Reverser drive hydrostatic fixed 
displacement motor, disassembled ........................................ 9.4.8
Reverser drive, disassembled .............................................. 3.1.34
Right-hand drive belts  ............................................................ 7.3.1
Right-hand drum bearing, 
disassembled ......................................................................... 3.4.4
Right-hand straw chopper bearing assembly, 
disassembled ......................................................................... 6.1.3
Right-hand threshing mechanism drive  ................................. 7.6.1
Rocker arm drive .................................................................... 4.5.1
Rotary coupling, disassembled  ............................................ 9.5.16
Rotary screen ......................................................................... 8.1.1
Rotary screen drive .............................................................. 7.17.1
Rotary screen drive, disassembled ...................................... 7.17.3
Rotary screen suction blower, 
disassembled ....................................................................... 8.1.11
Rotary screen, disassembled ................................................. 8.1.3

S

Safety features  ......................................................................  1.4.4
Safety Rules  ..........................................................................  1.2.1
Scenes of failures on the Orbitrol steering unit ......................  2.2.1
Sectional view of machine  .....................................................  1.6.1
Self-locking bolts  ...................................................................  1.3.1
Servo gearshift  ..................................................................  7.19.25
Servo gearshift, disassembled  ..........................................  7.19.27
Setting the engine speed control hydraulic cylinder
(from serial no. ...)  ...............................................................  9.6.15
Setting the engine speed control hydraulic cylinder
(up to serial no. ...) ...............................................................  9.6.26
Setting the track width  .......................................................  7.21.13
Sieve pan ...............................................................................  4.2.1
Sieve pan drive ....................................................................  7.13.1
Sieve pan drive V-belt pulley, disassembled  .......................  7.13.2
Sieve pan, disassembled .....................................................  4.2.20
Sieves – Basic setting
(electric sieve adjustment – from serial no. ...)  ......................  4.2.5
Sieves – Basic setting
(electric sieve adjustment – up to serial no. ...)  .....................  4.2.9
Slip clutch of cutterbar drive (1), dismantled  .........................  7.4.5
Some advice for speedy and correct repair work  ..................  1.3.4
Spare parts  ............................................................................  1.3.1
Specifications ........................................................................  1.5.1
Stage 1 chopper drive V-belt pulley, 
disassembled .......................................................................  7.10.3
Stage 1 fan drive V-belt pulley, 
disassembled .......................................................................  7.14.1
Stage 2 chopper drive V-belt pulley, 
disassembled .......................................................................  7.10.8
Stage 3 chopper drive V-belt pulley, 
dismantled .........................................................................  7.10.17
Steering .................................................................................  2.2.1
Steering axle ........................................................................  7.21.1
Steering axle bearing, disassembled .................................  7.21.18
Steering column, disassembled .............................................  2.2.7
Steering cylinder, disassembled ............................................  9.7.3
Stichwortverzeichnis ............................................................  11.1.1
Straw chopper  .......................................................................  6.1.1
Straw chopper drive hydraulic cylinder, 
disassembled .......................................................................  9.5.29
Straw spreader bearing housing, 
disassembled .......................................................................  7.11.5
Straw spreader drive  ...........................................................  7.11.1
Stub axle, disassembled ....................................................  7.21.10
Supporting arm, disassembled  ..............................................  3.6.9

T

Taper fittings on hydraulic lines  .............................................  1.3.3
Taper ring fasteners  ..............................................................  1.3.1
Tensioning the steel roller chains  ..........................................  1.3.1
Threshing concave  ................................................................  3.2.1
Threshing drum .....................................................................  3.4.1
Threshing drum reduction gearbox ........................................  7.7.1
Threshing drum reduction gearbox, 
disassembled .........................................................................  7.7.6
Threshing drum variable-speed drive 
3/3-way valve, disassembled .................................................  9.8.8

Summary of Contents for LEXION 480



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for LEXION 480

Parker RC Series Maintenance Instructions preview
RC Series
Brand: Parker Pages: 5
Bacharach Fyrite INSIGHT Operating & Maintenance Instructions preview
Fyrite INSIGHT
Brand: Bacharach Pages: 31
Backyard Play Systems 4105 Instruction Manual preview
4105
Brand: Backyard Play Systems Pages: 52
Backyard Play Systems 4030 Instructions Manual preview
4030
Brand: Backyard Play Systems Pages: 19
Backyard Play Systems 4030 Manual preview
4030
Brand: Backyard Play Systems Pages: 44
Bacharach Monoxor III Specification Sheet preview
Monoxor III
Brand: Bacharach Pages: 2
Eaton PowerXL DX-NET-ETHERNET2-2 User Manual preview
PowerXL DX-NET-ETHERNET2-2
Brand: Eaton Pages: 48
Eaton Power Xpert C445 Manual preview
Power Xpert C445
Brand: Eaton Pages: 2
Taylor-Wharton XL Series Instructions Manual preview
XL Series
Brand: Taylor-Wharton Pages: 25
i-CAT FLX V Series User Manual preview
FLX V Series
Brand: i-CAT Pages: 96
unios Echo Quick Installation Manual preview
Echo
Brand: unios Pages: 2
Sagola 4240 Instruction Manual preview
4240
Brand: Sagola Pages: 62
Garden Treasures 60031 Quick Start Manual preview
60031
Brand: Garden Treasures Pages: 2
Zimmer OptonPro Operating Instructions Manual preview
OptonPro
Brand: Zimmer Pages: 54
Zimmer Cryo 6 Manual preview
Cryo 6
Brand: Zimmer Pages: 4
Zimmer Biomet Tricera Instruction Manual preview
Tricera
Brand: Zimmer Biomet Pages: 23
Zimmer XYR Series Installation And Operating Instructions Manual preview
XYR Series
Brand: Zimmer Pages: 16
Zimmer XYR Series Installation And Operating Instructions preview
XYR Series
Brand: Zimmer Pages: 2

Brands by name

Popular brands

Load more brands