manualshive.com logo in svg

Canon Arizona 1300 Series, User Manual

The Canon Arizona 1300 Series offers outstanding print quality and performance. Enhance your printing experience with our comprehensive User Manual, available for free download at manualshive.com. This manual provides in-depth instructions and insights to help you maximize the full potential of your Canon Arizona 1300 printer.

Share
Download
background image

Index

A

AC power.................................................................

65

AC power plug........................................................

65

Alphanumeric input................................................

44

B

Batch job nesting....................................................

77

Beacon Light Status...............................................

29

C

Carriage Collision...................................................

81

Carriage Guard.......................................................

40

Carriage Interlock...................................................

29

Composite batch job nesting.................................

77

Configure remote assistance...............................

228

Coolant Reservoir.................................................

207

Custom Vacuum Zones....................................

70

, 

72

E

Emergency Stop Function.....................................

29

Emergency Stops...................................................

40

Emergency-Stop button.........................................

29

Enable Remote Service connection....................

225

F

foot switch...............................................................

94

G

Gantry Rails...................................................

206

, 

208

Graphical User Interface........................................

42

I

ICC profile -.............................................................

80

Imperial Vacuum Zones...................................

70

, 

72

Ink Bag...................................................................

176

ink delivery............................................................

174

Ink Filters.........................................................

40

, 

175

ink safety...............................................................

174

Ink System Status...................................................

45

Install software updates with Remote Service...

229

Install software updates without Remote
Service...................................................................

231

Ionization.......................................................

122

, 

123

Ionizer bar.....................................................

122

, 

123

M

Maintenance.........................................................

180

Maintenance Station......................................

40

, 

181

Measurement Units................................................

56

Media Adhesion......................................................

81

Media shaft.............................................................

94

Media Storage........................................................

80

media thickness......................................................

66

Metric Vacuum Zones......................................

70

, 

72

MSDS Ink Information .........................................

174

N

Nesting....................................................................

77

network connection settings.................................

55

Nozzle check..........................................................

181

Nozzle dropout......................................................

181

nozzle plate...........................................................

181

Nozzle print.............................................................

45

Nozzle print narrow................................................

45

O

Onscreen Keyboard................................................

42

Operator Control Station.......................................

40

Operator Interface Module Tabs...........................

42

P

Pause/Resume button............................................

45

Periodic Maintenance.............................................

42

Print button.............................................................

67

Print Job Control....................................................

44

Print Modes.............................................................

45

Print Modes Explained...........................................

45

Print Parameters.....................................................

45

Printhead maintenance........................................

181

R

Remote assistance

Configure........................................................

228

Remote Service

Enable connection..........................................

225

Index

245

Summary of Contents for Arizona 1300 Series

























































































































































































































































Reviews:

No comments

Related manuals for Arizona 1300 Series

Xerox B210 Manual preview
B210
Brand: Xerox Pages: 73
Xerox B210 Installation Manual preview
B210
Brand: Xerox Pages: 2
3D Systems CubePro Setup And Repacking Manual preview
CubePro
Brand: 3D Systems Pages: 26
3D Systems CubePro Repair Manual preview
CubePro
Brand: 3D Systems Pages: 39
3D Platform WorkSeries 200 Series Quick Reference Manual preview
WorkSeries 200 Series
Brand: 3D Platform Pages: 9
Dascom TALLY MIP480 User Manual preview
TALLY MIP480
Brand: Dascom Pages: 138
Dascom T2150 User Manual preview
T2150
Brand: Dascom Pages: 166
Radio Shack DMP-200 Operation Manual preview
DMP-200
Brand: Radio Shack Pages: 62
Oki C6150dn Material Safety Data Sheet preview
C6150dn
Brand: Oki Pages: 48
Oki C5100n Installation Instructions Manual preview
C5100n
Brand: Oki Pages: 20
Oki B2500 MFP Guía Del Usuario preview
B2500 MFP
Brand: Oki Pages: 42
Oki B2500 MFP Setup Manual preview
B2500 MFP
Brand: Oki Pages: 2
Oki C810n Accessory Installation Manual preview
C810n
Brand: Oki Pages: 8
Oki B 4600n Installation And Training Module preview
B 4600n
Brand: Oki Pages: 13
Oce CS9065 Features & Specifications preview
CS9065
Brand: Oce Pages: 2
Oki MB460MFP Guía Del Usuario preview
MB460MFP
Brand: Oki Pages: 193
Pantum M6500 series Faq preview
M6500 series
Brand: Pantum Pages: 126
TRENDnet TEW-MP1U (French) Manual D'Installation Rapide preview
TEW-MP1U
Brand: TRENDnet Pages: 14

Brands by name

Popular brands

Load more brands