manualshive.com logo in svg

Canon Arizona 1300 Series, User Manual

The Canon Arizona 1300 Series offers outstanding print quality and performance. Enhance your printing experience with our comprehensive User Manual, available for free download at manualshive.com. This manual provides in-depth instructions and insights to help you maximize the full potential of your Canon Arizona 1300 printer.

Share
Download
background image

Varnish Workflow Overview

Introduction

Arizona printers with the Varnish Option can overprint varnish on top of a printed image in
selected areas in a print job or as a flood coat. The printing of varnish applies only to flatbed
printing and is not available with the RMO.

NOTE

The Varnish option is not available for print jobs that use the High Definition print mode. Varnish

can be used with all other print modes.

Printing varnish creates a high value-added special effect. However, since this is an additional
process after printing image data, it also decreases productivity. Due to the low productivity of
printing large areas of varnish, it is best to concentrate the use of this feature on spot decoration.
Fortunately, the Arizona printer "blank space" skipping feature skips over areas in the print that do
not contain varnish, and greatly improves the net productivity of spot applications.

Varnish is printed as a second process after the CMYK(W) image is printed. Immediately after
printing a CMYK(W) image. The gantry moves to the start of image position and prints a varnish
spot or printer generated flood data using three additional passes.

NOTE

Varnish is actually "clear ink" and is for decorative purposes only. It does not provide additional

protection to the printed image.

Spot Versus Printer Flood Fill

Varnish data can be applied to a print job in two ways: Printer Flood Fill or Spot Data.
• A Printer Flood Fill is like an auto-fill that is done by the printer, where varnish data fills the

entire bounding box (the rectangular area that defines the total perimeter) of the image.

• Varnish Spot data can be defined in image editing applications such as Adobe Illustrator® or

with the Spot Layer tool in the ONYX workflow.

The Spot Data can be defined as either Spot 1 or Spot 2. The same spot data can be used to print
either varnish or white ink, or both.

Varnish Workflow Data Preparation

Varnish print job output can be accomplished in a variety of ways depending on the desired
results and preferred working process. There are three primary methods. The workflow options
are:
• Printer flood fill configuration,
• ONYX software Spot Layer Tool, and
• Varnish spot data image preparation.

Printer Flood Fill Configuration

 in the ONYX workflow does not require any pre-rip file

preparation and is the easiest method of achieving varnish output. All that is required is to
configure ONYX to use a Varnish Flood. The printer flood encompasses the bounding box (the
outer border of the image) of the file being processed.

ONYX Software Spot Layer Tool

 offers many options to process an image, and thus allows

various possible configuration choices. You can save these configurations as Filters and place
them in a Quick Set and this makes it possible to re-create with minimal effort settings that are
often used. All work with the Spot Layer tool requires an ONYX media profile with at least one
spot colour.

Varnish Workflow Overview

130

Chapter 9 - Manage a White Ink Workflow

Summary of Contents for Arizona 1300 Series

























































































































































































































































Reviews:

No comments

Related manuals for Arizona 1300 Series

SA F1 Series Installation And Operation Manual preview
F1 Series
Brand: SA Pages: 5
Xerox 3270 Programmer'S Manual preview
3270
Brand: Xerox Pages: 34
NCR 7197 Owner'S Manual preview
7197
Brand: NCR Pages: 5
IBM 3160 Introduction And Planning Manual preview
3160
Brand: IBM Pages: 102
Canon PIXMA MG5600 Series User Manual preview
PIXMA MG5600 Series
Brand: Canon Pages: 4
Fuji Xerox ApeoSport C5540I Quick Reference Manual preview
ApeoSport C5540I
Brand: Fuji Xerox Pages: 108
GCC Technologies Elite 12/1200N Software Installation preview
Elite 12/1200N
Brand: GCC Technologies Pages: 8
Felix printers FELIX Pro 3 Touch Quick Start Manual preview
FELIX Pro 3 Touch
Brand: Felix printers Pages: 29
Xerox DocuColor 45087638 User Addendum preview
DocuColor 45087638
Brand: Xerox Pages: 28
Konica Minolta IC-414 Installation Manual preview
IC-414
Brand: Konica Minolta Pages: 12
Kyocera KM-C2525E Service Manual preview
KM-C2525E
Brand: Kyocera Pages: 12
Konica Minolta Bizhub C20P Quick Manual preview
Bizhub C20P
Brand: Konica Minolta Pages: 46
TVS electronics CHAMPION MSP 450 User Manual preview
CHAMPION MSP 450
Brand: TVS electronics Pages: 92
Oki B2520 Brochure & Specs preview
B2520
Brand: Oki Pages: 2
Nagel 2S Trimmer Installation Manual preview
2S Trimmer
Brand: Nagel Pages: 22
D-Link DPR-1260 - RangeBooster G Multifunction Print Server User Manual preview
DPR-1260 - RangeBooster G Multifunction Print Server
Brand: D-Link Pages: 55
D-Link DPR-1061 Quick Installation Manual preview
DPR-1061
Brand: D-Link Pages: 49
Sawgrass Technologies QuickConnect II Getting Started Manual preview
QuickConnect II
Brand: Sawgrass Technologies Pages: 53

Brands by name

Popular brands

Load more brands