Canon Arizona 1300 Series User Manual Download Page 24 | Manualshive

Page: 24 / 248

background image

Actions in response to troubles

WARNING

• Immediately turn OFF the power switch and unplug the power cord from the power outlet

when a piece of metal, water or any other similar foreign matter gets inside the machine.
Then call your authorised service representative.

• Immediately stop using the machine when the machine becomes excessively hot, emits

smoke, or produces unusual odours or noises. Immediately turn OFF the power switch and
unplug the power cord from the power outlet. Then call your authorised service
representative.

• Immediately stop using the machine when the machine has been dropped or a cover is

damaged. Immediately turn OFF the power switch and unplug the power cord from the
power outlet. Then call your authorised service representative.

• In emergency situations, stop the machine immediately using an emergency stop switch.
• In the event of damage to the covers, power cable or operating elements, or penetration of

fluids or foreign bodies, contact your authorised service representative.

CAUTION

• Some areas inside the machine become hot. Do not touch the locations which are labelled

with the ”CAUTION HOT” symbol . Touching these areas can cause injuries.

• In event of a fire or smoke of the machine:

• Poisonous gases can be produced in any fire. They can also result from a fire in this

machine.

• Self-contained breathing apparatus must be worn when fighting fire or smoke emission.

Instructions to this effect should be stored at the fire alarm centre and with the local fire
department.

Consumables, supplies and maintenance materials

WARNING

• Do not throw toner or ink, toner or ink containing parts or contaminated parts, into an open

flame.

• Do not leave toner or ink, containing parts or contaminated parts, within reach of children.
• Store consumables, supplies and maintenance materials away from containers for food and

drink.

• Be careful when handling fluids. Clean up spilled fluids immediately, to minimise the risk of

slipping and serious injuries.

Safety and Environment Information

24

Chapter 3 - Safety Information

«
...
22
23
24
25
26
...
»

Summary of Contents for Arizona 1300 Series

























































































































































































































































Reviews:

No comments

Related manuals for Arizona 1300 Series

Brand: TDT Pages: 15

Brand: Samsung Pages: 2

Brand: Samsung Pages: 2

Brand: Samsung Pages: 341

Brand: Samsung Pages: 8

CLX2160N - Color Laser - All-in-One

Brand: Samsung Pages: 118

CLX 3160FN - Color Laser - All-in-One

Brand: Samsung Pages: 142

CLP-770ND - Color Laser Printer

Brand: Samsung Pages: 2

CLP 610ND - Color Laser Printer

Brand: Samsung Pages: 114

Brand: Samsung Pages: 6

Brand: Samsung Pages: 15

CLP 600N - Color Laser Printer

Brand: Samsung Pages: 227

CLP 600N - Color Laser Printer

Brand: Samsung Pages: 118

CLP 300N - Network-ready Color Laser Printer

Brand: Samsung Pages: 94

CJX-2000FW Series

Brand: Samsung Pages: 2

4116 - SCX B/W Laser

Brand: Samsung Pages: 205

3561ND - B/W Laser Printer

Brand: Samsung Pages: 252

3561ND - B/W Laser Printer

Brand: Samsung Pages: 127

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands