Canon Arizona 1300 Series User Manual Download Page 237 | Manualshive

Page: 237 / 248

background image

Use of controls, adjustments or performance of procedures other than those specified in this
User Documentation may result in hazardous radiation exposure. This is a semiconductor
laser. The maximum power of the laser diode is

0.5 mW

.

Lamps (All countries)

This product may contain lamps that are only intended for use in combination with and for this
specific product (and related equipment), and such lamps are not intended for use in other
applications.

Battery labelling (EEA including Switzerland)

• This product contains a battery. Please do not remove the battery. If the battery needs

replacement, this should be done only by skilled service technicians who are aware of the
removal instructions provided by Canon.

• This product contains a battery or batteries. It (They) is (are) located in (a) printed circuit

board(s) that is (are) essential for the continuous error-free functioning of the product. The
battery or batteries should be removed only by skilled service technicians who are aware of the
removal instructions provided by Canon.

•

Location

Battery capacity

Contains

Internal controller

200 mAh

Lithium type

Caution: Canon does not accept any liability for any damage or consequences, if the batteries
are removed by persons other than Canon service personnel.

Battery Labelling (USA)

This product contains a Lithium battery, containing Perchlorate Material – special handling may
apply, see

"http://www.dtsc.ca.gov/hazardouswaste/perchlorate"

Battery labelling (Taiwan)

Translation: Waste batteries, please recycle.

Chapter 13 - Regulation Notices

237

«
...
235
236
237
238
239
...
»

Summary of Contents for Arizona 1300 Series

























































































































































































































































Reviews:

No comments

Related manuals for Arizona 1300 Series

Brand: Qls Pages: 53

Brand: Xerox Pages: 36

Brand: DataCard Pages: 2

Brand: Oki Pages: 40

Brand: Oki Pages: 104

Brand: Oki Pages: 28

Brand: Oki Pages: 23

Brand: Oki Pages: 108

Brand: Oki Pages: 2

Brand: Oki Pages: 94

Brand: Oki Pages: 135

Brand: Oki Pages: 97

Brand: Oki Pages: 280

Brand: Oki Pages: 123

Pacemark PM4410

Brand: Oki Pages: 144

Pacemark PM4410

Brand: Oki Pages: 28

Brand: Oki Pages: 176

Magicolor 2 plus

Brand: QMS Pages: 90

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands