Canon Arizona 1300 Series User Manual Download Page 118 | Manualshive

Page: 118 / 248

background image

3.

Bend the height adjuster (small triangle in the top corner of the edge protector) slightly and then
straighten it again. This results in a slight bend (no more than a media thickness), that allows the
media edge to move more freely under the protector.

[48] Media Edge Protector Height Adjuster

IMPORTANT

If the height adjuster area is higher than 1 mm from the platen, there is a possibility that
the carriage may hit the edge of the protector and thus damage printhead nozzles.

4.

Peel the backing layer from the double-sided tape on the back of the protector.

5.

Place the bent edge of the protector into the media cut guide, but do not press down on the tape
yet.

6.

Slide the protector towards the media edge until the inside edge of the height adjuster is
positioned over the media edge (see figure below).

NOTE

Do not let the plastic edge near the arc butt up against the media edge or the device may
not let the media pass smoothly.
The vacuum in the platen will hold the main part of the protector in place while the image
is printed.

Media Edge Protectors

118

Chapter 7 - Roll Media Option

«
...
116
117
118
119
120
...
»

Summary of Contents for Arizona 1300 Series

























































































































































































































































Reviews:

No comments

Related manuals for Arizona 1300 Series

Pixma MG2400 Series

Brand: Canon Pages: 2

Brand: Xerox Pages: 24

Brand: Samsung Pages: 165

Brand: Samsung Pages: 2

Inkjet SCX-1150F

Brand: Samsung Pages: 66

Brand: Samsung Pages: 155

CLX-3170FN series

Brand: Samsung Pages: 220

CLX 6210FX - Color Laser - All-in-One

Brand: Samsung Pages: 36

CLX-3160 Series

Brand: Samsung Pages: 139

Brand: Samsung Pages: 8

Lazett Combo SCX-4016

Brand: Samsung Pages: 2

Brand: Samsung Pages: 319

Brand: TallyGenicom Pages: 92

DC240 - DocuColor 240 Color Laser

Brand: Xerox Pages: 2

ColourLaser series guide

Brand: Xante Pages: 31

Brand: Xante Pages: 31

Accel-a-Writer 812

Brand: Xante Pages: 12

Brand: Xante Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands