Canon Arizona 1300 Series User Manual Download Page 176 | Manualshive

Page: 176 / 248

background image

Change Ink Bags

Introduction

The ink is supplied in collapsible bags. An ink bag can be replaced at any time. An ink bag can be
changed during a print job. It is not necessary to stop the printer.

When to do

Ink bags should be replaced if:
• The printer displays an "Error: ink fill timed out" message.
• The operator sees that the bag is empty.
• An ink bag is nearly empty and the operator wants to leave the printer unattended during a

long print and does not want the ink to run out. The nearly empty bag can be reconnected and
used up later when the operator is present.

CAUTION

Wear gloves when contact with ink or maintenance materials is possible. Gloves should always
overlap sleeves. Follow the ink related Safety Data Sheets (SDS) guidelines carefully in order to
ensure maximum safety. For example use Ansell Microflex 93-260 gloves, which offer a
protection against UV inks and flush up to one hour. Pollution with other chemicals can shorten
the protection time against UV inks and flush.
Wear eye protection as prescribed in this document when performing a task or action in this
area.

CAUTION

UV inks and flush liquids can be harmful if not properly handled. Follow always the Safety Data
Sheets (SDS) guidelines carefully in order to ensure maximum safety.

Remove the Quick-Release Coupler

Change Ink Bags

176

Chapter 10 - Ink System Management

«
...
174
175
176
177
178
...
»

Summary of Contents for Arizona 1300 Series

























































































































































































































































Reviews:

No comments

Related manuals for Arizona 1300 Series

IMAGEPRESS C7010VPS

Brand: Canon Pages: 4

iP2600 - PIXMA Color Inkjet Printer

Brand: Canon Pages: 2

Brand: Canon Pages: 8

ImageCLASS 2300

Brand: Canon Pages: 102

Brand: NCR Pages: 5

Brand: Panasonic Pages: 24

Brand: Oki Pages: 40

Workio DP-1820E

Brand: Panasonic Pages: 38

Magicolor 2 plus

Brand: QMS Pages: 90

Magicolor 2 Desklaser

Brand: QMS Pages: 4

Brand: QMS Pages: 8

Brand: QMS Pages: 94

Brand: QMS Pages: 6

Brand: BIXOLON Pages: 31

ApeoSport C5540I

Brand: Fuji Xerox Pages: 108

Brand: Colorjet Pages: 52

AficioSP C410DN

Brand: Ricoh Pages: 204

Beta Prusa Standard

Brand: 2PrintBeta Pages: 67

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands