Canon Arizona 1300 Series User Manual Download Page 64 | Manualshive

Page: 64 / 248

background image

Training Requirements

Introduction

The operator must receive training for safety issues, printer operation, and the appropriate ONYX
Thrive software prior to operating the printer.

Safety Training

Before operating the Arizona 1300 Series printer, make sure you have read and understood all of
Chapter 3 "Safety Guidelines".

Operator Training

For optimal safety and print quality, all printer operators must have received training by qualified
service personnel. training provides a general orientation to printer safety and operating
procedures. This User Guide is not a substitute for official training.

ONYX Workflow Training

Maximum performance from the printer requires a properly trained operator. trains the operator
in the use of the printer hardware and software at installation. However, this is not a substitute
for formal training.

Operators must be fully versed in the operation of ONYX Thrive Workflow software . For any
operator unfamiliar with their operation, training is required. Training courses are available;
contact your local representative for an ONYX-certified training program.

Training Requirements

64

Chapter 5 - Operate the Printer

«
...
62
63
64
65
66
...
»

Summary of Contents for Arizona 1300 Series

























































































































































































































































Reviews:

No comments

Related manuals for Arizona 1300 Series

RS/6000 44P Series 270

Brand: IBM Pages: 216

Brand: iFactory3D Pages: 39

Brand: Zebronics Pages: 6

Brand: BIXOLON Pages: 29

Printpix NC-400D

Brand: FujiFilm Pages: 47

ApeosPort C5570

Brand: Fuji Xerox Pages: 290

Brand: Flashforge Pages: 63

Brand: DataCard Pages: 5

Brand: Canon Pages: 2

Xs463de - Mono Laser Mfp P/C/S 40Ppm 1200X

Brand: Lexmark Pages: 104

Brand: Ricoh Pages: 192

Brand: FELIXprinters Pages: 55

Brand: Seaory Pages: 7

Brand: Polymaker Pages: 16

Brand: PosDelta Pages: 31

Brand: POS-X Pages: 4

Brand: Kodak Pages: 129

Brand: Kodak Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands