Canon Arizona 1300 Series User Manual Download Page 175 | Manualshive

Page: 175 / 248

background image

Ink Bags in the Ink Bay

Ink Filters

The printheads in your printer are protected from contaminants in the ink by means of ink filters.
These are easily accessed and can be replaced by the operator when they become blocked with
debris (see the Maintenance section "Change Ink Filters").

NOTE

A loss of pigment when printing a nozzle check or long ink fill times indicates that a filter is

clogged and must be replaced.

How to Store and Handle UV Ink

To ensure print quality and to extend the life of printheads in your printer, UV inks must be
properly handled and stored correctly.
• Inks must be stored within a temperature range of 5 - 30°C (41 - 86°F). Exposure to extreme

temperatures will reduce the expected life of the ink.

• Do not use ink that is past the expiry date.
• Store in cool, dry place and keep away from heat and direct sunlight.

White Ink

If your printer has the white ink option and white is not printed on a regular basis, pigment
settling can occur in the white ink printheads. During periods of white ink inactivity, the printer
will automatically try to maintain the white ink channel using the following methods:
• ink recirculating
• spitting

Additional efforts may be required to recover nozzle performance for the white ink printheads.

Arizona Printer LED Ink

Chapter 10 - Ink System Management

175

«
...
173
174
175
176
177
...
»

Summary of Contents for Arizona 1300 Series

























































































































































































































































Reviews:

No comments

Related manuals for Arizona 1300 Series

ImageCLASS MF3240 Series

Brand: Canon Pages: 62

ImageCLASS MF4270

Brand: Canon Pages: 226

imageCLASS D660

Brand: Canon Pages: 8

ImageCLASS MF3240 Series

Brand: Canon Pages: 136

Color imageRUNNER C5180 Series

Brand: Canon Pages: 851

imageCLASS D320

Brand: Canon Pages: 121

imageCLASS MF212w

Brand: Canon Pages: 236

imageCLASS D760

Brand: Canon Pages: 82

imageclass LBP251dw

Brand: Canon Pages: 72

ImageCLASS MF4270

Brand: Canon Pages: 248

ImageCLASS MF4270

Brand: Canon Pages: 36

imageCLASS D760

Brand: Canon Pages: 8

imageCLASS MF4100 Series

Brand: Canon Pages: 140

imageclass LBP251dw

Brand: Canon Pages: 116

imageCLASS D860

Brand: Canon Pages: 73

imageCLASS D1320

Brand: Canon Pages: 36

ImageCLASS MF3240 Series

Brand: Canon Pages: 15

imageCLASS D550

Brand: Canon Pages: 116

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands