manualshive.com logo in svg

Canon Arizona 1300 Series, User Manual

The Canon Arizona 1300 Series offers outstanding print quality and performance. Enhance your printing experience with our comprehensive User Manual, available for free download at manualshive.com. This manual provides in-depth instructions and insights to help you maximize the full potential of your Canon Arizona 1300 printer.

Share
Download
background image

Arizona Printer LED Ink

Introduction

Your Arizona printer uses IJC357 LED UV-curable ink. Daily and weekly maintenance activities are
necessary to maintain optimum printing performance. Due to the use of UV LED curing
technology, the ink is effectively cured immediately after printing, but a small residual curing
effect can continue for up to 24 hours. In most cases, the printed material can be handled or cut
directly after printing.

Managing Your UV-curable Ink

Your printer is optimized for UV-curable ink supplied by Canon. The ink is supplied in a
collapsible bag. To install ink on the printer, the bag is inverted and a quick connect coupler is
engaged. This opens up the flow path for the ink. The bags contain tags that identify them to the
printer when they are loaded. This allows the printer to ensure that the correct ink is loaded.

Ink bags have several benefits over bottles or cartridges:

Self-collapsing bags make it easy to see how much ink remains in each bag.
• Virtually all the ink is successfully extracted from the bag by the printer, reducing the otherwise

costly waste of usable ink.

• Ink changes are performed without mess or spills, keeping the environment around the printer

clean.

• Ink changes can be performed during printing. This prevents waste prints and lost time.

Only qualified ink can be used. If a bag of ink with an invalid serial number, expired use-by date,
incorrect colour placement in the ink bay, or if an expired tag is connected to the printer, then the
operator is alerted and an error message is displayed.

Access to SDS Ink Information

Safety Data Sheets (SDS) for the ink and Flush are available from http://downloads.cpp.canon.
Read and periodically review this safety information to ensure optimal safe handling procedures.
Follow proper emergency responses when using UV inks and flush.

CAUTION

Wear gloves when contact with ink or maintenance materials is possible. Gloves should always

overlap sleeves. Follow the ink related Safety Data Sheets (SDS) guidelines carefully in order to

ensure maximum safety. For example use Ansell Microflex 93-260 gloves, which offer a

protection against UV inks and flush up to one hour. Pollution with other chemicals can shorten

the protection time against UV inks and flush.

Wear eye protection as prescribed in this document when performing a task or action in this

area.

IMPORTANT

Do not install ink that is not certified by Canon for use in this printer, as this may result in poor

quality prints, uncured ink in the finished prints and permanent damage to the ink pumps, filters,

ink lines or printheads.

Arizona Printer LED Ink

174

Chapter 10 - Ink System Management

Summary of Contents for Arizona 1300 Series

























































































































































































































































Reviews:

No comments

Related manuals for Arizona 1300 Series

Xerox All in One Printer Product Safety Data Sheet preview
All in One Printer
Brand: Xerox Pages: 3
WANHAO CGR Series User Manual preview
CGR Series
Brand: WANHAO Pages: 29
Panasonic KX-P8415 Operating Instructions preview
KX-P8415
Brand: Panasonic Pages: 3
Panasonic KX-P7105 Operating Instructions preview
KX-P7105
Brand: Panasonic Pages: 4
Xerox 4215 Operator'S Manual preview
4215
Brand: Xerox Pages: 414
MakerBot Replicator Mini+ Quick Start Manual preview
Replicator Mini+
Brand: MakerBot Pages: 2
MakerBot Replicator Mini Compact Reference Manual preview
Replicator Mini Compact
Brand: MakerBot Pages: 38
MakerBot Replicator 2 Quick Start Manual preview
Replicator 2
Brand: MakerBot Pages: 14
SainSmart Prusa i3 Troubleshooting Manual preview
Prusa i3
Brand: SainSmart Pages: 13
Xerox CX Visual Reference Manual preview
CX
Brand: Xerox Pages: 12
Unimark ET6000 Installation And Operator'S Manual preview
ET6000
Brand: Unimark Pages: 38
Swift STP512B User Manual preview
STP512B
Brand: Swift Pages: 14
Radio Shack Daisy Wheel 410 Service Manual preview
Daisy Wheel 410
Brand: Radio Shack Pages: 140
G&G IMAGE L2550DW Series User Manual preview
IMAGE L2550DW Series
Brand: G&G Pages: 147
Plas-Ties A401870 Series Manual preview
A401870 Series
Brand: Plas-Ties Pages: 18
Edimax Past Ethernet Combo Print Server PS-1216U Quick Installation Manual preview
Past Ethernet Combo Print Server PS-1216U
Brand: Edimax Pages: 23
zeepro zim User Manual preview
zim
Brand: zeepro Pages: 31
SATO GT 424e Parts List preview
GT 424e
Brand: SATO Pages: 46

Brands by name

Popular brands

Load more brands