Canon Arizona 1300 Series User Manual Download Page 40 | Manualshive

Page: 40 / 248

background image

Operator Interface Hardware

Introduction

The Operator interacts with printer components to print, maintain, and monitor the state of the
printer. This section identifies and explains the functions of the hardware.

[17] Printer Hardware

Operator Interface Components

Hardware Interface Components

Component

Function

1) Main Power Switch

Turns the printer On and Off.

2) Emergency Stops

Emergency stop buttons can shut down all motion and hazardous
systems. There are three E-stops, one on the Operator Control Sta-
tion, and one on each end of the gantry.

3) Carriage Guard

Protects the operator from exposure to UV light and stops all mo-
tion if dislodged by an obstacle.

4) Registration Pins

Allow the operator to register media by placing it against the pins.
Registration pin operation can be set at the user interface to work
in either manual or automated mode. Pins can be enabled or disa-
bled individually.

5) Printer Status Beacon

Indicates printer status. See Chapter 3 for details.

6) UV Lamps

UV light is used to cure the ink.

7) Vacuum Gauge

Displays the strength of the table vacuum system. If it reads less
than 10"Hg, check for vacuum leaks.

4

Operator Interface Hardware

40

Chapter 4 - Navigate the User Interface

«
...
38
39
40
41
42
...
»

Summary of Contents for Arizona 1300 Series

























































































































































































































































Reviews:

No comments

Related manuals for Arizona 1300 Series

imagePROGRAF W8400

Brand: Canon Pages: 24

Super G3 FAX Board-T1

Brand: Canon Pages: 16

imagePROGRAF TZ-30000

Brand: Canon Pages: 66

imagePROGRAF W7200

Brand: Canon Pages: 126

imagePROGRAFi iPF840 series

Brand: Canon Pages: 149

Brand: Canon Pages: 166

iP4000 - PIXMA Photo Printer

Brand: Canon Pages: 2

iP4000 - PIXMA Photo Printer

Brand: Canon Pages: 3

Brand: Canon Pages: 21

Brand: Olympus Pages: 3

BW Remote Operators Software Kit-A1

Brand: Canon Pages: 20

imageRUNNER 2420

Brand: Canon Pages: 30

Brand: Canon Pages: 51

imageCLASS LBP325dn

Brand: Canon Pages: 252

Brand: DataCard Pages: 2

Brand: Xerox Pages: 8

Brand: Javelin Pages: 2

COLOR SYSTEM 110

Brand: Oce Pages: 392

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands