BYD L3 AUTO Owner'S Manual Download Page 93

Page: 93 / 202

BYD L3

AUTO Owner’s Manual

Automobile Multimedia System

1-85

Troubleshooting for multimedia player

Failure

Reason

Solution

No poweror sound

1. The ignition switch is

not turned on.

2. The wire is not

connected properly.

3. The fuse breaks.

Turn the vehicle key to ―ACC‖

or ―ON‖.

2. Check the wire connection.

3. Change a fuse with specified

specification.

No sound with disk put in

1. The disk is put in

reversely.

2. The disk is dirty or

scratched seriously.

1. Put in the disk correctly.

2. Wipe the disk or change a

new one

Unstable sound caused

by vibration

1. Installation is infirm.

2. The disk is dirty or

scratched seriously.

1. Fix the machine with

installation parts.

2. Clean up the disk or change a

new one.

Can not store channels

and the preset broadcast

The battery line is

connected improperly.

Connect the cable to correct pole.

The noise sent by FM

stereophony and single

channel broadcast give

are too loud

The broadcasting station

is far away or the signal is

excessively weak.

Choose other broadcasting station

with stronger signal.

Using of multimedia

Refer to <User’s Manual of L3 Multimedia Syste

Summary of Contents for L3 AUTO











































































































































































































Search results

Summary of Contents for L3 AUTO

Reviews:

Related manuals for L3 AUTO

Brands by name

Popular brands

BYD L3 AUTO, Owner'S Manual

Search results

Summary of Contents for L3 AUTO

Reviews:

Related manuals for L3 AUTO

Brands by name

Popular brands