manualshive.com logo in svg

BYD L3 AUTO, Owner'S Manual, Page: 146 / 202

Share
Download
BYD L3 AUTO Owner'S Manual Download Page 146

BYD L3 

AUTO Owner’s Manual

 

 

4-10 Emergency Treatment

 

 

 
Before installation, please brush off all 
corrosive materials on the installation 
surface  with  a  wire  brush.  During 
installation,  the  metal  area  on  the 
installation  surfaces  must  be  in  well 
contact  with each other, or the  wheel 
bolts may get loose, which may cause 
the tire falling off in driving. 
 
 

 

Reinstall Wheel Bolts 

 

 

 
7. 

Reinstall 

all 

wheel 

bolts 

manually. 

 

 
To  reinstall  bolts,  please  manually 
tighten them with wedged end inward 
first. Push the wheel backward and try 
to further tighten the bolts manually.   
 
 
 
 
 
 
 

TIPS

 

Do  not  apply  engine  oil  or 
lubricant on the bolts, or they will 
get  loose,  which  may  cause  the 
wheel  detached  and  lead  to 
serious  accident.

。

If  there  is 

engine  oil  or  lubricant  on  the 
bolts 

or 

nuts, 

clean 

them 

immediately. 

 

 
Lower Down Vehicle   

 

 

 
8.  Lower  down  the  car  to  ground 
and tighten the wheel bolts. 

 

 
 

Summary of Contents for L3 AUTO











































































































































































































Reviews:

No comments