BYD L3 AUTO Owner'S Manual Download Page 162

Page: 162 / 202

BYD L3

AUTO Owner’s Manual

6-4 Maintenance Instructions

Requirements for Maintenance Program

BYD L3 auto must be maintained according to the normal maintenance

program (you can refer to “Maintenance Program”).

If the car is operated under the following one or more special conditions, some maintenance item is required to be
performed more frequently.

A. Road Conditions

Drive on rugged, muddy or
snowmelt road

Drive on the dusty road

B. Driving Conditions

When the car has towed a trailer;
used a camping trailer or top
clamping bracket

When the car has run at a short
distance repeatedly below 0

℃

within 8km.

When the car has idled for a long time or
long run at a low speed such as police
car, taxi or delivery car.

Summary of Contents for L3 AUTO











































































































































































































Search results

Summary of Contents for L3 AUTO

Reviews:

Related manuals for L3 AUTO

Brands by name

Popular brands

BYD L3 AUTO, Owner'S Manual

Search results

Summary of Contents for L3 AUTO

Reviews:

Related manuals for L3 AUTO

Brands by name

Popular brands