BYD L3 AUTO Owner'S Manual Download Page 21

Page: 21 / 202

BYD L3

AUTO Owner’s Manual

Keys and car door

1-13

interference is found and do
not

use

until

the

interference

has

been

eliminated.



When using a micropower

radio

device,

must

withstandby  interference  of
radio  services  and  radiation
interference  from  industrial,
scientific

and

medical

devices.



intelligent key near aircrafts
or airports.

Replace Electronic Intelligent Key
Battery

Replacement  of  the  battery  may
damage the key. It is recommended to
have BYD service station replace the
battery.  If  you  have  to  replace  it  by
yourself,  please  use  flat  screwdriver
and  CR1632  lithium  battery  or
equivalents.

WARNING

Pay close attention to prevent the
battery or components from being
swallowed by children.

NOTICE



Do not touch the circuit with
hands, otherwise the static
produced may damage the
key.



Do not leave out any
components when replacing
the key battery.



Only

use

batteries

recommended

BYD

service station or their
equivalent for replacement.



Dispose depleted battery
according to local laws.

Replace the electronic intelligent key
battery in the following steps.

1. Pull down release switch and take
out mechanical key.
2. Open electronic key cover with a
flat screwdriver or similar tools.

Summary of Contents for L3 AUTO











































































































































































































Search results

Summary of Contents for L3 AUTO

Reviews:

Related manuals for L3 AUTO

Brands by name

Popular brands

BYD L3 AUTO, Owner'S Manual

Search results

Summary of Contents for L3 AUTO

Reviews:

Related manuals for L3 AUTO

Brands by name

Popular brands