BYD L3 AUTO Owner'S Manual Download Page 171

Page: 171 / 202

BYD L3

AUTO Owner’s Manual

Self-maintenance 7-5

NOTE

◆

Remember, storage battery

and ignition coil bears high
current or high voltage. Pay
attention to short circuit caused
by accidents.

◆

If the coolant overflows, you

must wash it with water, to
avoid

damaging

the

components or paint finish.

◆

Do not drop any dirt or any

other things into the spark plug
hole.

◆

Do not lever up the external

electrode of spark plug at the
side of central electrode.

◆

You can only use the specified
spark plug. Using other spark
plug may damage the engine or
generate radio interference.

◆

Do not fill too much power

steering fluid, or the power
steering gear may be damaged.

◆

If the brake fluid overflows,

you must wash it with water, to
avoid

damaging

the

components or paint finish.

◆

Do not drive with the air filter

taken down, otherwise it may
cause excessive wear of engine
and meanwhile backfire will
cause

fire

the

engine

compartment.

◆

Notes: do not scratch the

glass by the wiper bracket.

◆

In closing the engine cover,

check if any tools or cloths are
left in the engine compartment.

Location of Jack

Front

Back

Summary of Contents for L3 AUTO











































































































































































































Search results

Summary of Contents for L3 AUTO

Reviews:

Related manuals for L3 AUTO

Brands by name

Popular brands

BYD L3 AUTO, Owner'S Manual

Search results

Summary of Contents for L3 AUTO

Reviews:

Related manuals for L3 AUTO

Brands by name

Popular brands