BYD L3 AUTO Owner'S Manual Download Page 149 | Manualshive

Page: 149 / 202

background image

BYD L3

AUTO Owner’s Manual

Emergency Treatment 4-13

NOTE

◆

Please use the specified

towing hook, or the car may be
damaged.

◆

Do not tow the car from the

rear side with all four wheels on
the ground, or it will seriously
damage the transmission.

The  driver  should  sit  inside  steering
the car and controlling the brake.
Towing in this way may only move the
car  slowly  for  a  short  distance  on  a
hard  road.  Meanwhile  it  requires  that
the  wheels,  shafts,  transmission,
drivetrain,  steering  wheel,  and  brake
be in good condition.

TIPS

Take  special  care  when  towing
the  car.  Please  avoid  sudden
startup  and  unstable  driving
operation,  which  may  exert  great
stress  on  emergency  towing
hook,  and  towing  cable/chain.
The hook, towing cable/chain may
crack, in which case there may be
serious

personal

injury

or

damage to the car.

NOTE

Please use the towing cable or
chain designed specifically for
car towing. Tie the cable or chain
to the towing hook firmly.

Before towing, please release the
parking

brake

and

set

the

transmission to N gear. The ignition
switch should be at "ACC" (engine
shut down) or "ON" (engine running).

TIPS

When the engine is not running,
boosters of brake and steering
device do not work, which makes
steering

and

braking

more

difficult than usual.

«
...
147
148
149
150
151
...
»

Summary of Contents for L3 AUTO











































































































































































































Reviews:

No comments

Related manuals for L3 AUTO

Brand: Jeep Pages: 212

BLACK STEEL S2560

Brand: Fab Fours Pages: 9

Brand: Barker Pages: 2

Brand: Toyota Pages: 35

Brand: Westin Pages: 3

Brand: Fab Fours Pages: 21

Fleetwood Brougham Sedan 1966

Brand: Cadillac Pages: 56

Brand: r.LiNK Pages: 20

Brand: Honda Pages: 10

2DA 008 136-031

Brand: Hella Pages: 2

Brand: Prime Design Pages: 8

Brand: Aries Pages: 3

Brand: Volvo Pages: 16

Brand: PERODUA Pages: 43

Brand: SAAS Pages: 3

Brand: Nuna Pages: 29

GRAND CHEROKEE 4xe 2023

Brand: Jeep Pages: 440

Brand: Emerson Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands