background image

BYD L3 

AUTO Owner’s Manual

 

 

 

3-6 Starting and Driving

 

Make  sure  viscosity  of  the  engine 
oil is suitable for driving in winter.   

 
Please  refer  to  section  7-2  for 
information 

on 

recommended 

viscosity  of  engine  oil.  If  a  large 
volume  of  engine  oil  for  summer  use 
is  left  in  the  engine  in  winter,  it  may 
cause  difficulty  for  engine  starting.  If 
you  are  not  sure  about  choosing 
engine  oil,  please  contact  BYD 
service station for help.   

 
Avoid Door Lock Freezing   

Spray some deicing agent or glycerin 
in  door  lock  hole  to  prevent  the  lock 
from freezing.   

 
Use Cleanser with Antifreeze 

It is available in BYD service stations 
and all auto part stores. Mixing ratio of 
water  and  antifreeze  shall  follow 
manufacturer's instruction.   
 

NOTE

 

Don’t  use  engine  antifreeze  or 
other  substitutes  as  cleanser,  as 
they  will  damage  the  vehicle 
paint.

 

Do not apply parking brake if it may 
be frozen up.   

In parking, shift to gear shift lever to N 
gear and place obstacles around rear 
wheels to retain the car. Do not apply 
parking brake  as it may be frozen up 
by water or snow, resulting in difficulty 
to release the parking brake.   

 
Prevent  snow  from  staying  under 
mudguard.   

Snow  or  ice  under  mudguard  may 
make  steering  difficult.  When  driving 
in  winter,  you  shall  stop  the  check 
regularly to check whether there is ice 
or snow under mudguard.   

 
You  are  recommended  to  keep 
certain emergency tools on the car 
according to your region.   

Examples  of  such  articles  are  tire 
chains,  window  wiper,  a  bag  of  sand 
or  salt,  flasher  signaling  device, 
shovel and connection cables.   
 
 

Tow Trailer   

 

BYD L3 is designed for transportation 
of  passengers.  Towing  a  trailer  may 
pose 

bad 

effect 

to 

operation, 

performance,  braking,  endurance, 
fuel  economy  of  the  car.      Safety 
and  comfort  in  driving  depends  on 
proper use of devices and the driver’s 
habitual care in driving.   
For the sake of safety of yourself and 
others, do not over load the car or tow 
a  trailer.Damage  or  failure  cause  by 
towing  a  trailer  for  business  purpose 
is not covered by BYD warranty.   

 
Weight Limit   

Before towing a trailer, make sure it is 
within  the  car’s  capacity.  You  can 
contact  the  local  BYD  service  station 
to check the trailer's capacity.   
Towing capacity is measured on level 
road.  In  region  with  high  altitude, 
please  take  note  that  the  engine 
power  and  its  towing  capacity  will 
reduce.     
 
 
 

Summary of Contents for L3 AUTO











































































































































































































Reviews: