BYD L3 AUTO Owner'S Manual Download Page 196

Page: 196 / 202

BYD L3

AUTO Owner’s Manual

7-30 Self-maintenance

3. Rotate the light seat anticlockwise
manually and pull it outwards to
remove the light seat.

4. Rotate the bulb anticlockwise and
pull it outwards to remove the bulb.

The steps of installation is opposite to
disassembly.

Rear combination lamp

The steps of replacing rear turn signal
light and rear fog light is the same as
backup light.

The steps of installation is opposite to
disassembly.

High Mount brake light

1. Rotate the light seat anticlockwise
manually and pull it outwards from the
hole of rear shelf.

2.Pull off the bulb from light seat,
replace the bulb. If it is not convenient,
pull out the connector.

Summary of Contents for L3 AUTO











































































































































































































Search results

Summary of Contents for L3 AUTO

Reviews:

Related manuals for L3 AUTO

Brands by name

Popular brands

BYD L3 AUTO, Owner'S Manual

Search results

Summary of Contents for L3 AUTO

Reviews:

Related manuals for L3 AUTO

Brands by name

Popular brands