background image

BYD L3 

AUTO Owner’s Manual

 

 

 

3-4 Starting and Driving

 

connection are proper.   

 
Cables

:  check  whether  there  is 

damaged,  loose  or  disconnected 
cable.   

 
Fuel  Pipe:

  check  whether  there  is 

leakage  or  bad  connection  in  fuel 
pipe. 
 

TIPS

 

Do not leave children’s toys in the 
car, which may pose potential 
danger, especially in hard braking 
and collision, in which case the 
toys may cause personal injury.

 

 

After Engine Starting   
 
Exhaust  System

:  listen  to  the  noise 

to check whether there is any leakage. 
If  any  leakage,  you  shall  have  it 
repaired 

immediately. 

(Refer 

to 

Engine Exhaust Warning

‖ in Chapter 

2.) 

 
Engine  Oil  Level

:  shut  down  the 

engine and stop the car on flat ground, 
then  check  oil  level  with  a  dipstick.   
(Refer to description in section 7-2.)

 

 
In Driving   
Instruments: 

make 

sure 

maintenance  prompting  indicators 
and speedometer work normally.   

 
Brake

:  under  safe  traffic  conditions, 

make  sure  braking  does  not  result  in 
deviation of the car.   

 
Other Abnormalities

: check whether 

there 

is 

any 

leakage 

or 

bad 

connection,  and  listen  for  abnormal 
noise.   
If no abnormality is found out, you can 
enjoy your driving now.   

Driving 

Tips 

Under 

Certain 

Conditions 

 
●  Driving  slowly  in  head  wind,  which 

is helpful for operating of the car.     

●  When  driving  the  car  to  climb  the 

roadside 

curbstone, 

keep 

low 

speed  and  proper  direction  .  Avoid 
driving  on  any  objects  with  sharp 
edges  or  on  any  road  block. 
Otherwise  the  tires  may  suffer 
severe damage such as explosion.   

● Slow down vehicle speed on rugged 

roads. 

Otherwise 

tires 

and/or 

wheels will suffer severe damage.   

● Brake may be wet after washing the 

car  or  driving  on  road  under  deep 
water.  To  check  whether the  brake 
is  wet,  make  sure  the  environment 
is  safe  and  then  step  on  the  brake 
pedal  slightly.  If  you  feel  that  the 
braking  force  is  abnormal,  the 
brake may be wet. To dry the brake, 
slightly  step  on  the  braking  pedal 
while  driving  the  car  carefully  with 
parking brake applied.   

 
 
 
 

Summary of Contents for L3 AUTO











































































































































































































Reviews: