BYD L3 AUTO Owner'S Manual Download Page 76

Page: 76 / 202

BYD L3

AUTO Owner’s Manual

1-68 Instruments and Maintenance Indicators



Prompt Information Display

Display

descriptio

n or

buzzer

tone

Description

Key is not

detected

If key is not detected,

this information will be

displayed after

pressing starting

switch.

Low key

battery

This information

prompts key battery is

running low. Please

change battery.

Parking

braking is

not

released.

When vehicle speed

is over 5km/h and the

parking braking is not

released, this

information will be

displayed with buzzer

warning.

Please

refill fuel

When remaining fuel

is low, this information

will be displayed with

buzzer warning.



Fault Information Display

Display

descriptio

n or

buzzer

tone

Description

Oil
mileage

The expected travel
mileage

the

remaining fuel, which is
calculated

combination of average
fuel consumption and
instant

fuel

consumption.

The

actual mileage may be
different

from

this

value.

Average
speed

The  average  vehicle
speed  since  the  last
resetting;  press  ―DISP‖
button for 2 seconds to
reset this item.

Clock
setting

Clock

and

date

adjustment

increment

cycle

mode.

Driving
time

The time after engine
starting or the last

Display
item

Description

Clock

When the power supply
is at ON, the clock will
always be displayed.

Date

When the power supply
is at ON, the date will
be displayed by default.

Fuel
consump
tion

The

total

fuel

consumption since the
last

resetting,

press

―DISP‖  button  for  2
seconds  to  reset  this
item.

Average
fuel
consump
tion

The

average

fuel

consumption  /  100  km
since  the  last  resetting;
press  ―DISP‖  button  for
2  seconds  to  reset  this
item.

Instant
fuel
consump
tion

Instant

fuel

consumption amount.

Summary of Contents for L3 AUTO











































































































































































































Search results

Summary of Contents for L3 AUTO

Reviews:

Related manuals for L3 AUTO

Brands by name

Popular brands

BYD L3 AUTO, Owner'S Manual

Search results

Summary of Contents for L3 AUTO

Reviews:

Related manuals for L3 AUTO

Brands by name

Popular brands