BYD L3 AUTO Owner'S Manual Download Page 49

Page: 49 / 202

BYD L3

AUTO Owner’s Manual

Seat, Seatbelt, Steering wheel, Rear-view Mirror and Sunroof

1-41

Driver and front passenger side
airbags(Optional)

Your vehicle has side airbags to help
protect the upper body of the driver or
a front seat passenger during a

moderate or severe side impact.

Curtain airbag(Optional)

Your vehicle has curtain airbags to
help protect the head of the driver or a
front seat passenger during a
moderate or severe side impact.

Please contact a BYD authorized
service station in case of the following
problems:



The curtain airbag and side

airbag have been inflated.



The front part of the vehicle

(shaded part in the figure) is affected
in an accident; but it’s not serious
enough to trigger the airbag.



The panel part of the seat with

side airbag(shaded parts in the figure)
is scratched, cracked

Summary of Contents for L3 AUTO











































































































































































































Search results

Summary of Contents for L3 AUTO

Reviews:

Related manuals for L3 AUTO

Brands by name

Popular brands

BYD L3 AUTO, Owner'S Manual

Search results

Summary of Contents for L3 AUTO

Reviews:

Related manuals for L3 AUTO

Brands by name

Popular brands