BYD L3 AUTO Owner'S Manual Download Page 147 | Manualshive

Page: 147 / 202

background image

BYD L3

AUTO Owner’s Manual

Emergency Treatment 4-11

To lay down the car, please rotate the
jack handle counterclockwise.
Please  use  a  spanner  for  wheel  bolt
to  tighten  the  bolts.  Do  not  use  any
other tools or lever, like hammer, tube,
or your feet.
Make  sure  the  spanner  is  fitted  onto
the bolts firmly.
As  per  the  order  shown  in  the  figure
above, tighten the bolts slightly one by
one, repeat the procedure until all the
bolts are fastened firmly.

TIPS

● Please make sure no part of

your body and no one nearby
will get injured while laying
down the car onto the ground.

● When the tire is replaced,

please use the spanner with a
torque of 103N·

m (10.5 kgf·

m) to

fasten  the  bolts.  Otherwise  the
bolts will  get  loose, which  may
cause  the  tire  falling  off  and
result in serious accident.

After Tire Replacement

9.

The

tire

pressure

after

replacement.

Adjust  the  tire  pressure  to  the  value
specified  in  Chapter  8.  If  the  current
pressure is lower than specified value,
please  drive  the  car  slowly  to  the
nearby

service

station

for

air

charging.

Do  not  forget  to  install  the  tire  valve
cap,  or  dust  and  moisture  will  enter
the  valve  core  to  cause  possible  air
leakage.  If  the  tire  valve  cap  is
missing,  please  use  a  new  one
immediately.

10. Put tools, jack and flat tire in
proper storage.

After  tire  replacement,  please  use  a
torque  spanner  to  tighten  the  wheel
bolts  to  the  torque  specified  in
Chapter  8.  The  flat  tire  should  be
repaired by a qualified technician.

TIPS

Before  driving,  please  make  sure
all  tools,  jack,  and  flat  tire  are
fixed  in  their  storage  position  so
as  to  reduce  the  possibility  of
personal injury in case of a crash
or emergency braking.

If the Car Gets Stuck

If the car gets stuck in snow, mud, or
sand, please try to get it out by
pushing it forward or backward.

TIPS

If  there  are  persons  or  objects
near  the  car,  please  do  not  try  to
move  the  car  by  pushing  it
forward  and  backward.  If  not,
once  the  car  gets  out  and
suddenly

moves

forward

or

backward, there may be personal
injury or damage to objects.

«
...
145
146
147
148
149
...
»

Summary of Contents for L3 AUTO











































































































































































































Reviews:

No comments

Related manuals for L3 AUTO

Brand: A-Tach Mounts Pages: 2

GRAND CHEROKEE 2023

Brand: Jeep Pages: 108

Brand: Code 3 Pages: 8

Brand: Honda Pages: 4

SAFESTOP SS0005

Brand: Pro-gard Pages: 4

Brand: Prorack Pages: 20

Brand: E&G Classics Pages: 2

Brand: Scion Pages: 24

Brand: v.link Pages: 21

Brand: Rugged Ridge Pages: 3

Brand: GARO Pages: 15

Brand: Skoda Pages: 324

Brand: TATA Motors Pages: 308

Ridesmart KMA-610

Brand: KlipXtreme Pages: 12

Brand: Metra Electronics Pages: 10

Brand: Wallbox Pages: 21

Brand: T-Tech Pages: 1

Platinum Pro Plug-in

Brand: Haltech Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands