BYD L3 AUTO Owner'S Manual Download Page 122

Page: 122 / 202

BYD L3

AUTO Owner’s Manual

2-10 Tips on Driving BYD L3

transmission

oil

temperature

reaches 60

℃

- Park the car on flat ground or slope.
- Step on foot brake pedal.
- Wait for 2 seconds.
-

Shift gear to ―N‖ (Neutral) gear.

- Wait for 10 seconds.
-

Shift gear to ―P‖ (Parking) gear.

- Let the engine run idle.
- Pull off oil level plug screw.
- Make sure at least 0.2L oil flows out

after  removing  the  oil  level  plug
screw.  (If  the  oil  outflow  is  less,  it
means  the  original  oil  amount  is
insufficient.)

- Wait for a few minutes until the oil

droplet falls off from the plug screw
opening.

- Reinstall the oil level plug screw.
- Shut down the engine.

Note: During refilling transmission oil,
prevent it from overflow. In Case of
overflow, clean up overflowing oil
immediately

Drain
plug (1)

Oil level
plug (2)

Oil filling

plug (3)

Summary of Contents for L3 AUTO











































































































































































































Search results

Summary of Contents for L3 AUTO

Reviews:

Related manuals for L3 AUTO

Brands by name

Popular brands

BYD L3 AUTO, Owner'S Manual

Search results

Summary of Contents for L3 AUTO

Reviews:

Related manuals for L3 AUTO

Brands by name

Popular brands