BYD F3DM Owner'S Manual Download Page 148 | Manualshive

Page: 148 / 214

background image

- 148 -

F3DM Owner’s Manual

WARNING

Removal of the radiator cap Under
high temperature can cause the
antifreeze to spray out, and serious
injury may be resulted from scalding
fluid and steam blown out under
pressure.
Always let the engine and radiator
cool down before removing the
radiator cap.

6. When the antifreeze temperature
be cooled to normal, check the
antifreeze level in the tank again and
add additional antifreeze up to the
maximum scale mark if necessary.
Large drop of antifreeze level means
leakage in the system. Please contact
BYD authorized dealer for immediate
examination.

If the Car Has Flat Tires

Turn on the emergency flashlight.
Drive slowly along the shoulder until
you get to an exit or an area to stop a
safe place away from the traffic lanes.
Park the car on firm, level and non-
slippery ground.
Put the transmission in P and apply the
parking brake.
Turn the ignition switch to “LOCK”
position.
All the passengers get out of the car
on the side away from traffic.
Read the following instructions
carefully.

WARNING

To reduce the possibility of serious
personal injury, please obey the
instructions below when you lift the
car by a jack.

y

Follow the directions for changing

a tire exactly, and never get
under the vehicle when it is
supported only by the jack

y

When the car is lifted by a jack,

do not start and run the DM
system.

y

Park the car on firm, level and

non-slippery ground, apply
parking brake tightly and shift
the transmission to P gear. If
necessary, block the wheel
diagonally opposite to the one
being changed.

y

Make sure to set the jack properly

!

!

使用手册小330.indd 148

2011-4-13 18:36:52

«
...
146
147
148
149
150
...
»

Summary of Contents for F3DM























































































































































































































Reviews:

No comments

Related manuals for F3DM

Brand: Kia Pages: 385

Brand: Sirius Satellite Radio Pages: 8

Brand: Motoalliance Pages: 8

Brand: Saab Pages: 288

Brand: Sunsky Pages: 9

Brand: Chevrolet Pages: 412

Brand: Ford Pages: 256

Brand: JANE Pages: 58

Brand: TEINHOF Pages: 2

Brand: Quadratec Pages: 14

Stargazer Spirit XTR Skylight

Brand: Lippert Pages: 8

1500 CLASSIC 2020

Brand: RAM Pages: 360

Brand: Car-Interface Pages: 23

Brand: Whispbar Pages: 14

QuadraTop Adventure Top S

Brand: Quadratec Pages: 13

Brand: T-Tech Pages: 1

Brand: SkyRack Pages: 2

Brand: pewag Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands