BYD F3DM Owner'S Manual Download Page 153 | Manualshive

Page: 153 / 214

background image

- 153 -

F3DM Owner’s Manual

WARNING

Do not apply engine oil or lubricant
on the nuts, or they will get loose,
w h i c h m a y c a u s e t h e w h e e l
detached and lead to serious
accident. If there is engine oil or
lubricant on the bolts or nuts, clean
them immediately.

Lower Down Vehicle

8. Lower down the car to ground and
tighten the wheel bolts.
To lay down the car, please rotate the
jack handle counterclockwise.
Please use a wheel wrench to tighten
the wheel bolts. Do not use any other
tools or lever other than your hands,
like hammer, tube, or your foot. Make
sure the wrench is securely engaged
over the bolts.
As per the order shown in the figure
above, tighten the bolts slightly one by
one, repeat the procedure until all the
bolts are fastened firmly.

WARNING

y

Please make sure no part of your

body and no one nearby will get
injured while laying down the car
onto the ground.

y

After the tire is replaced, Have

the wheel bolts tightened with
torque wrench to 110N·

ｍ

(11.5

kgf·m). Otherwise if the torque
is insufficient, the nuts will get
loose, which may cause the
tire fell off and result in serious
accident.

After Tire Replacement
9. The tire pressure after replacement.
Adjust the tire pressure to the
specification specified in Chapter 8.
If the current pressure is lower than
specified, please drive the car slowly
to the nearby service station for air

!

!

使用手册小330.indd 153

2011-4-13 18:36:52

«
...
151
152
153
154
155
...
»

Summary of Contents for F3DM























































































































































































































Reviews:

No comments

Related manuals for F3DM

GRAND CHEROKEE 2023

Brand: Jeep Pages: 108

Brand: C-KO Pages: 4

Brand: Buick Pages: 161

Brand: Aries Pages: 3

ASENTO EV-COLC15R

Brand: ADAPT SOLUTIONS Pages: 22

Brand: MovaNext Pages: 4

Brand: Genesis Pages: 690

Brand: TrailPRO Pages: 3

Brand: Gold Lantern Pages: 1

Brand: Metec Pages: 2

Brand: Intellitronix Pages: 11

Brand: Edelbrock Pages: 1

Brand: Toyota Pages: 422

Brand: Chevrolet Pages: 416

Brand: Yamaha Pages: 13

Brand: Yamaha Pages: 26

Brand: Yamaha Pages: 46

Brand: Yamaha Pages: 98

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands