BYD F3DM Owner'S Manual Download Page 151 | Manualshive

Page: 151 / 214

background image

- 151 -

F3DM Owner’s Manual

Unscrew wheel nuts

3. Unscrew all bolts on the flat tire.
Unscrew all bolts on the wheel before
lifting the car.
Unscrew the bolts on the wheel anti-
clockwise. For better torque, you can
fit the wrench to the nut with its handle
on the right side, as shown in the figure
above. Grip at the end of the wrench
handle and pull upwards. Please avoid
the wrench slipping off the nut.
Do not remove the nuts, just loosen
them.

Jack Positioning

4. Place the jack under the proper
lifting point, as shown in the figure.
Make sure that the jack is placed on
the flat and solid ground.

Lift the Vehicle

5. Make sure nobody is in the car, and
lift up the car to a height that allows
installation of spare tire.
Please notice that it needs larger
ground clearance to install the spare
tire than removing the flat tire.
To lift up the car, please insert the
jack handle into the jack (loose joint)
and rotate it clockwise. When the
jack touches the car and starts lifting,
please check again if the jack is at the
right position.

使用手册小330.indd 151

2011-4-13 18:36:52

«
...
149
150
151
152
153
...
»

Summary of Contents for F3DM























































































































































































































Reviews:

No comments

Related manuals for F3DM

Brand: LaserTrack Pages: 12

DAF POWERCHOICE 250A

Brand: Paccar Pages: 20

Brand: DEFA Pages: 9

Slim Line LED Light Grille Kit

Brand: rough country Pages: 8

Car Cup Holder Phone Mount

Brand: UGREEN Pages: 9

Code Alarm PROFESSIONAL SERIES CA 5550SST

Brand: Audiovox Pages: 14

Brand: AC Schnitzer Pages: 16

PRIME DESIGN VRR-E-PM21

Brand: Safe Fleet Pages: 12

Brand: Jeep Pages: 16

Brand: Audi Pages: 4

Brand: SCC Pages: 4

STO N SHO SNS 144

Brand: Big Mikes Performance Parts Pages: 7

Brand: Lincoln Pages: 10

Brand: Vauxhall Pages: 131

2011 A3 Sportback

Brand: Audi Pages: 29

Brand: Warn Pages: 5

Brand: Camoplast Pages: 19

Brand: Acura Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands