Buell 2004 XB9S Service Manual Download Page 423 | Manualshive

Page: 423 / 597

background image

4-114 2004 Buell Lightning: Fuel System

HOME

FUEL TANK VENT VALVE

4.40

GENERAL

The vent valve opens to allow gas vapor to escape the fuel
tank and either vent to the atmosphere or to the charcoal can-
ister on California Models (EVAP-equipped) and closes to
prevent gasoline from leaking out of the fuel tank if the vehicle
is tipped at an extreme angle.

NOTE

The fuel tank must be drained to perform this service.

REMOVAL

1.

Drain fuel tank. See

DRAINING FUEL TANK

under

4.39

FUEL PUMP

.

2.

Remove fuel tank vent line from vent valve.

3.

See

Figure 4-95.

Remove vent valve fasteners (5).

4.

Remove bracket (4), vent valve (3) and o-ring (2) from
fuel tank/frame (1).

INSTALLATION

1.

See

Figure 4-95.

Install new vent valve o-ring (2).

2.

Install vent valve (3) into fuel tank/frame. Vent valve noz-
zle should be at approximately the 7:00 position.

3.

Install bracket over vent valve. Slot in bracket should line
up with notch in valve.

4.

Loosely install vent valve fasteners (5).

5.

Tighten fasteners to 39-41 in-lbs (4.4-4.6 Nm).

6.

Connect fuel tank vent line to vent valve.

7.

Install airbox. See

4.44 AIRBOX

.

8.

Install intake cover assembly. See

2.35 INTAKE COVER

ASSEMBLY.

9.

Connect negative battery cable. Tighten battery terminal
hardware to 60-96 in-lbs (7-11 Nm).

1

WARNING

1

WARNING

After installing seat, pull upward on front of seat to be
sure it is locked in position. If seat is loose, it could shift
during vehicle operation and startle the rider, causing
loss of control which could result in death or serious
injury. (70)

10. Install seat. See

2.41 SEAT.

Figure 4-94. Fuel Pump Drain Screw (swingarm removed

for illustration)

Figure 4-95. Fuel Tank Vent Valve

8774

1.

Fuel pump connector [86]

2.

Fuel pump drain plug

2

1

b1000x4x

1.

Fuel tank/frame

2.

O-ring

3.

Vent valve

4.

Bracket

5.

Fastener (2)

5

4

3

2

1

«
...
421
422
423
424
425
...
»

Summary of Contents for 2004 XB9S






















































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2004 XB9S

Brand: GAS GAS Pages: 34

Brand: R&G Pages: 8

Brand: Honda Pages: 3

Brand: BMW Pages: 16

Brand: RDMOTO Pages: 3

Brand: hepco & becker Pages: 6

Brand: hepco & becker Pages: 2

Brand: hepco & becker Pages: 3

SPORTRACK 670915 00 01

Brand: hepco & becker Pages: 2

Lock-it 5064564 00 01

Brand: hepco & becker Pages: 2

Easyrack 6626526 01 01

Brand: hepco & becker Pages: 4

Easyrack 6614526 01 01

Brand: hepco & becker Pages: 4

Brand: hepco & becker Pages: 2

Brand: hepco & becker Pages: 3

Brand: Smarter tools Pages: 28

crivit sports 101545

Brand: DELTA-SPORT Pages: 42

Brand: VESPA Pages: 64

Brand: Cagiva Pages: 407

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands