Berger Lahr WDP3-01X Manual Download Page 64

Page: 64 / 114

3.3.4

Value display on
front panel

The actual position and the software version can be displayed.

With an Interbus-S interface, d99 can be used for activating the diag-
nostic function.

Available for all device variants

Set AUTOM input inactive unless on-line command processing is
active.

Select the value to be displayed:

Display

Meaning

d0.0

Actual position digits representing ones

d0.1

Actual position digits representing thousands

d0.2

Actual position digits representing millions

d10

Software version

d99

Interbus-S diagnostic function

The Interbus-S diagnostics is activated with the d99 function and indi-
cates the following four states:

Operating voltage

RC Interbus-S link o.k.
BA

Interbus-S transmission active

RD No other Interbus-S slave available

U RC BA RD

Operation

3-12

WDP3-01X Ident. no.: 00441109760

Summary of Contents for WDP3-01X



















































































































Search results

Summary of Contents for WDP3-01X

Reviews:

Related manuals for WDP3-01X

Brands by name

Popular brands

Berger Lahr WDP3-01X, Manual

Search results

Summary of Contents for WDP3-01X

Reviews:

Related manuals for WDP3-01X

Brands by name

Popular brands