Berger Lahr WDP3-01X Manual Download Page 2

Page: 2 / 114

Safety requirements

Please read the following safety requirements prior to installation, operation, maintenance and repair
of the device.

•

The intended use of the device is described under “Purpose” and must be observed.

•

Installation, maintenance and repair of the device shall be performed by a qualified electrician.
National regulations concerning
–

accident prevention

–

installation of electrical and mechanical systems

–

radio interference suppression

shall be observed.

•

The technical data of the device, particularly the ambient conditions, shall be observed.

•

The device shall only be operated by trained personnel.

•

The warranty is invalidated in case of unauthorized modification or opening of the device.

•

Please ask your technical consultant prior to installing accessories not listed in the chapter
“Description of accessories”.

•

The safety symbols and notes on the device and in the manual shall be observed.

Explanation of symbols

ATTENTION
Reference to a danger for the device or components, possibly resulting
in the endangering of human life.
DANGER
Reference to a direct endangering of human life.

DANGER
High voltage at component, do not touch.

DANGER
High temperature at component, do not touch.

ATTENTION
Warning against electrostatic discharge (ESD).
Only touch the PC board or component in an electrostatically protected
environment.

NOTE
Important or additional information concerning the device or the manual.

Summary of Contents for WDP3-01X



















































































































Search results

Summary of Contents for WDP3-01X

Reviews:

Related manuals for WDP3-01X

Brands by name

Popular brands

Berger Lahr WDP3-01X, Manual

Search results

Summary of Contents for WDP3-01X

Reviews:

Related manuals for WDP3-01X

Brands by name

Popular brands