Berger Lahr WDP3-01X Manual Download Page 102

Page: 102 / 114

6.2.4.3

Setup

Wire the MP 924 interface distributor in accordance with fig. 6-7.
For interface conversion RS 232

↔

RS 485 (RS 422), use the

MP 923 interface converter (see chapter 6.2.3).

ATTENTION
The interface cables must be shielded on both ends (connect shield
on MP 924 to protective ground).

ATTENTION
Never connect a terminator.

If several MP 924 interface distributors are used, combine them as
illustrated in fig. 6-7.

Set the connected units to network mode and switch them on.

ATTENTION
The same baud rate must be set on all units for network mode.

ATTENTION
When using an MP 923 interface converter, at least one unit attached
to the first MP 924 interface distributor must be switched on in order
to ensure that power is supplied to the MP 923.

B1
B2
B3

MP 924

Unit 1

(RS 485 interface)

Unit 8

(RS 485 interface)

Unit 9

(RS 485 interface)

Shield connection

B1
B2
B3

MP 923

RS 232

RS 485

Fig. 6-7 MP 924 interface

distributor setup

Appendix

6-10

WDP3-01X Ident. no.: 00441109760

Summary of Contents for WDP3-01X



















































































































Search results

Summary of Contents for WDP3-01X

Reviews:

Related manuals for WDP3-01X

Brands by name

Popular brands

Berger Lahr WDP3-01X, Manual

Search results

Summary of Contents for WDP3-01X

Reviews:

Related manuals for WDP3-01X

Brands by name

Popular brands