3. General
c) Re-install the mounting screws. When properly adjusted, the end of each side rail will protrude through the slot in the rear
mounting bracket, once the chassis is rack mounted.
Image 3-12
To take advantage of this feature, ensure that there is at least 1/2” of clearance above the chassis.
Image 3-13
2. For the E2’s two keyhole slots, measure and install two rack screws in your equipment rack’s front rails. Allow each screw to
protrude approximately 3/4” from the surface of the rails.
3. Lift the chassis, and while supporting it, slide the side rails through the slots in the rear mounting brackets.
4. While continuing to support the chassis, slide the screws (in the front rails) through the two keyholes, and let the chassis settle
up into the keyhole slots.
5. Tighten the two lower screws, then install and tighten the two uppers screws in the rack rail.
How to install S3 or EX in a rack
Use the following steps to rack mount the S3 or the EX:
1. S3 and EX units are shipped with side rails included in the shipping case and not installed onto the chassis. These side rails,
when they are properly installed and adjusted, assist with the distribution of chassis (and cable) weight within your rack. Use the
following steps to properly adjust the side rails:
a) Measure and install the two supplied mounting brackets on your rear rack rails.
Image 3-14
R5905948 EVENT MASTER DEVICES 17/07/2017
39
Summary of Contents for S3 series
