6. EM GUI orientation
6.10 Con
fi
guration Menu > System modi
fi
er area
General
General parameters concerning the selected system are accessible in this area. The user can select the system’s preset con
fl
ict
mode, the native rate, and genlock mode.
Description
Image 6-13
•
Preset Con
fl
ict: Mode—
When using single layers con
fl
icts can arise when a Preset Recall modi
fi
es a source layer that is
currently on Program. You may choose from three Preset Con
fl
ict Modes to resolve these con
fl
icts.
-
Auto—
The system performs the necessary actions to gracefully recall the Preset to Program.
-
Force Recall—
The system recalls the Preset directly to Program. Program is not protected.
-
User Con
fi
rm—
The system presents the user with a pop-up asking what to do when a con
fl
ict is detected.
User Con
fi
rm options:
o
Resolve – All Trans or Cut:
Perform the necessary actions to resolve the con
fl
ict and perform an All Trans or Cut to
bring the Preset to Program.
o
Resolve – Wait:
Perform the necessary actions to resolve the con
fl
ict and wait for the user to press the All Trans or Cut
manually.
o
Cancel:
Cancels the entire Preset recall operation.
-
Off
—The system alerts the user with an error message about any Preset recall con
fl
ict, but it does not present a pop-up
menu for resolving the issue.
•
Preset Con
fl
ict: Time(frame)
is the amount of time the system uses when automatically performing an All Trans.
•
Native rate
: System native rate in Hz (Cycles in second). Available selections:
23.98
30
59.94
24
47.95
60
25
48
29.97
50
The native system rate needs to match the general frame rate in the event where the unit is used.
•
Genlock mode
: Selects the system genlock mode to
Freerun
or
Lock to External
.
•
Genlock Status
: Reports the system’s genlock mode status: Locked or not Locked.
•
H Offset
: The H sync can be offset to match a Genlock situation. Adjustment in mS.
•
V Offset
: The V sync can be offset to match a Genlock situation. Adjustment in mS.
•
Master VP
: Reports the units IP address in the local network.
•
Unit ID
: Reports the units ID number. ID required to identify different units are acting as a single or linked system in order to
expand for Inputs, Outputs or Layers.
R5905948 EVENT MASTER DEVICES 17/07/2017
103
Summary of Contents for S3 series
