ARM Musca-S1 Technical Reference Manual Download Page 69

Page: 69 / 194

Table 3-9 Secure Privilege Control Block registers (continued)

Offset

Name

Type

Reset value

Function

0x00B4

APBSPPPC1

0x0000_0000

Secure Unprivileged Access APB slave Peripheral. Protection Control
1. This register controls the PPC within the System Control element.

See the

Arm

CoreLink

™

SSE

‑

200 Subsystem for Embedded Technical

Reference Manual (r1p0)

for more information.

0x00C0

APBSPPPCEXP0

0x0000_0000

Expansion 0 Secure Unprivileged access APB slave Peripheral
Protection Control.

See

APBSPPPCEXP0 Register

on page 3-81

for information on how

this register is implemented in the Musca

‑

S1 test chip.

0x00C4

APBSPPPCEXP1

0x0000_0000

Expansion 1 Secure Unprivileged access APB slave Peripheral
Protection Control.

See

APBSPPPCEXP1 Register

on page 3-82

for information on how

this register is implemented in the Musca

‑

S1 test chip.

0x0FD0

PID4

0x0000_0004

Peripheral ID 4

0x0FE0

PID0

0x0000_0052

Peripheral ID 0

0x0FE4

PID1

0x0000_00B8

Peripheral ID 1

0x0FE8

PID2

0x0000_000B

Peripheral ID 2

0x0FEC

PID3

0x0000_0000

Peripheral ID 3

0x0FF0

CID0

0x0000_000D

Component ID 0

0x0FF4

CID1

0x0000_00F0

Component ID 1

0x0FF8

CID2

0x0000_0005

Component ID 2

0x0FFC

CID3

0x0000_00B1

Component ID 3

SECMPCINTSTATUS Register

The Secure

Memory Protection Controller

(MPC) Interrupt Status Register characteristics are:

Purpose

Stores the interrupt statuses of the

Memory Protection Controllers

(MPCs).

See the

Arm

CoreLink

™

SSE

‑

200 Subsystem for Embedded Technical Reference Manual (r1p0)

for more information.

Usage constraints

This register is read-only.

Memory offset and full register reset value

See

3.4.6 Secure Privilege Control Block

on page 3-66

The following table shows the bit assignments of the SECMPCINTSTATUS Register.

3 Programmers model

3.4 Base element

101835_0000_01_en

reserved.

3-69

Non-Confidential

Summary of Contents for Musca-S1


































































































































































































Search results

Summary of Contents for Musca-S1

Reviews:

Related manuals for Musca-S1

Brands by name

Popular brands

ARM Musca-S1, Technical Reference Manual

Search results

Summary of Contents for Musca-S1

Reviews:

Related manuals for Musca-S1

Brands by name

Popular brands