ARM Musca-S1 Technical Reference Manual Download Page 174

Page: 174 / 194

3.13

GPIO control registers

The Musca

‑

S1 test chip implements GPIO registers which control the GPIO interface.

Bits [15:0] control the Musca

‑

S1 test chip I/O to the Arduino Expansion Shield interface. Bits [31:16]

are reserved.

The base memory addresses of the GPIO control registers are:
•

0x4011_0000

in the Non

‑

secure region.

•

0x5011_0000

in the Secure region.

See the

Arm

Cortex

‑

M System Design Kit Technical Reference Manual

The following table shows the GPIO control registers in the Musca

‑

S1 test chip in address offset order

from the base memory address. Undefined registers are reserved. Software must not attempt to access
these registers.

Table 3-122 GPIO control registers summary

Offset

Name

Type Reset

Width Function

0x0000

GPIODATA

0x0000_0000

Data value.

Bits [31:16] are reserved.

0x0004

GPIODATAOUT

0x0000_0000

Data output value.

Bits [31:16] are reserved.

0x0010

GPIOOUTENSET

0x0000_0000

Output enable set.

Bits [31:16] are reserved.

0x0014

GPIOOUTENCLR

0x0000_0000

Output enable clear.

Bits [31:16] are reserved.

0x0020

GPIOINTENSET

0x0000_0000

Interrupt enable set.

Bits [31:16] are reserved.

0x0024

GPIOINTENCLR

0x0000_0000

Interrupt enable clear.

Bits [31:16] are reserved.

0x0028

GPIOINTTYPESET RW

0x0000_0000

Interrupt type set.

Bits [31:16] are reserved.

0x002C

GPIOINTTYPECLR RW

0x0000_0000

Interrupt type clear.

Bits [31:16] are reserved.

0x0030

GPIOINTPOLSET

0x0000_0000

Polarity

‑

level, edge IRQ configuration. Set interrupt polarity bit.

Bits [31:16] are reserved.

0x0034

GPIOINTPOLCLR

0x0000_0000

Polarity

‑

level, edge IRQ configuration. Clear interrupt polarity bit.

Bits [31:16] are reserved.

0x0038

GPIOINTSTATUS

INTCLEAR

0x0000_0000

Clear interrupt request.

Bits [31:16] are reserved.

3 Programmers model

3.13 GPIO control registers

101835_0000_01_en

reserved.

3-174

Non-Confidential

Summary of Contents for Musca-S1


































































































































































































Search results

Summary of Contents for Musca-S1

Reviews:

Related manuals for Musca-S1

Brands by name

Popular brands

ARM Musca-S1, Technical Reference Manual

Search results

Summary of Contents for Musca-S1

Reviews:

Related manuals for Musca-S1

Brands by name

Popular brands