ARM Musca-S1 Technical Reference Manual Download Page 151

Page: 151 / 194

Purpose

Selects either ALTF1 or ALTF2 as destination of input signals from MAIN input multiplexer for
Musca

‑

S1 test chip I/O PA31

‑

PA0.

See

3.11.1 IOMUX registers

on page 3-122

for information on the Musca

‑

S1 test chip I/O

multiplexer.

Usage constraints

There are no usage constraints.

Memory offset and full register reset value

See

3.11.2 SCC registers summary

on page 3-125

The following table shows the IOMUX_ALTF1_INSEL Register bit assignments.

Table 3-90 IOMUX_ALTF1_INSEL Register bit assignments

Bits

Name

Function

[31:0]

IOMUX_ALTF1_INSEL[31:0]

Selects either ALTF1 or ALTF2 as destination
of MAIN input multiplexer for Musca

‑

S1 test

chip multiplexed I/O PA31

‑

PA0:

0b0

: Select ALTF1_IN.

0b1

: Select ALTF2.

Reset value

0x0000_0000

Note

See

2.2.2 Test chip multiplexed I/O

on page 2-23

for the functions that are

available on the multiplexed Musca

‑

S1 test

chip I/O.

IOMUX_ALTF1_OUTSEL Register

The IOMUX_ALTF1_OUTSEL Register characteristics are:

Purpose

Selects either ALTF1_OUT or ALTF2 as output data for Musca

‑

S1 test chip I/O PA31

‑

PA0.

See

3.11.1 IOMUX registers

on page 3-122

for information on the Musca

‑

S1 test chip I/O

multiplexer.

Usage constraints

There are no usage constraints.

Memory offset and full register reset value

See

3.11.2 SCC registers summary

on page 3-125

The following table shows the IOMUX_ALTF1_OUTSEL Register bit assignments.

3 Programmers model

3.11 Serial Configuration Control registers

101835_0000_01_en

reserved.

3-151

Non-Confidential

Summary of Contents for Musca-S1


































































































































































































Search results

Summary of Contents for Musca-S1

Reviews:

Related manuals for Musca-S1

Brands by name

Popular brands

ARM Musca-S1, Technical Reference Manual

Search results

Summary of Contents for Musca-S1

Reviews:

Related manuals for Musca-S1

Brands by name

Popular brands